Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CYP RAX-PSU-12V
Summary of Contents for CYP RAX-PSU-12V
- Page 1 RAX-PSU-12V 12V DC Power Manager OPERATION MANUAL...
- Page 3 DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document.
- Page 4 SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
-
Page 5: Table Of Contents
CONTENTS 1. Introduction ...........6 2. Applications ...........6 3. Package Contents ........6 4. System Requirements ......6 5. Features ..........7 6. Operation Controls and Functions ..7 6.1 Front Panel ........... 7 6.2 Rear Panel ............. 8 6.3 WebGUI Control ......... 9 6.4 RS-232 Control ..........14 6.5 Telnet Control ..........14 6.6 RS-232 and Telnet Commands ....15 8. -
Page 6: Introduction
1. INTRODUCTION This 8-Port 12V DC Power Manager is a DC power splitter which can distribute up to 125 milliamps of 12 volt power to up to eight connected devices via 2-pin terminal block connections (115 watts total across all 8 outputs). -
Page 7: Features
6.1 Front Panel ISP/ RS-232 RESET RAX-PSU-12V RS-232: Connect directly to your PC/laptop using a 3.5mm mini- jack to 9-pin adapter to send RS-232 commands to control the unit. ISP/RESET: This button has multiple functions, see below. ISP MODE: Press and hold this button while powering the unit on to enter ISP mode. -
Page 8: Rear Panel
6.2 Rear Panel 12V POWER OUT A B 12V SERV. CONTROL DC 12V 12V POWER OUT & LEDs 1~8: Connect power cables with 3.5mm 2-pin terminal blocks from units requiring 12V power. Up to 8 devices can be powered. When power is available from a port, the associated LED will be green. -
Page 9: Webgui Control
6.3 WebGUI Control 6.3.1 Device Discovery Please obtain the “Device Discovery” software from your authorised dealer and save it in a directory where you can easily find it. Connect the unit and your PC/Laptop to the same active network and execute the “Device Discovery”... - Page 10 information window provides a convenient link to launch the WebGUI directly. 6.3.2 WebGUI Overview After connecting to the WebGUI’s address in a web browser, log into the unit by entering the appropriate user name and password. All primary functions of this unit are controllable via the built in WebGUI, including Status, Device Settings, Schedule, and System settings.
- Page 11 1) Power In: Displays the voltage, current and wattage of the unit’s main power supply. 2) Power Out: Displays the voltage, current and wattage of each of the 8 individual power outputs. 3) System Temperature: Displays the unit’s temperature as measured at 3 locations inside the case on the PCB.
- Page 12 Schedule The Schedule tab provides multiple ways to automate and schedule the powering on and off of any of the 8 power ports on this unit. 1) Repeat Mode: Items in this section will execute at their set times on the selected days (Sunday through Saturday) every week as long as they are marked as “Active”.
- Page 13 System This tab provides system configuration options including changing the network settings, downloading/restoring saved system configurations, modifying the username and password, system time setting, and updating the firmware. 1) Network: This section allows for setting the unit to either Static or DHCP mode for its IP information.
-
Page 14: Rs-232 Control
6.4 RS-232 Control Unit Controlling PC Serial Port Settings Pin Definition Pin Definition Baud Rate 19200 Data Bits Parity Bit None Stop Bits Flow Control None 6.5 Telnet Control Before attempting to use Telnet control, please ensure that both the unit and the PC are connected to the same active networks. -
Page 15: Rs-232 And Telnet Commands
6.6 RS-232 and Telnet Commands COMMAND Description and Parameters HELP Show the full command list. ? Show the full command list. HELP N1 Show a description of command N1. N1 = {Command Name} IPCFG Display the current IP configuration. IPSTATIC N1 N2 N3 ... - Page 16 COMMAND Description and Parameters PWR N1 NAME N2 Rename power output N1. N1 = 1 ~ 8 [Port number] N2 = {Name String} [16 characters max] PWR_STATUS N1 Show the current power state (volts, watts, amps) of power output N1 = 1 ~ 8 [Port number] TEMPERATURE ...
- Page 17 7. CONNECTION DIAGRAM RS-232 Equipped PC/Laptop RS-232 ISP/ RS-232 RESET RAX-PSU-12V 12V POWER OUT A B 12V SERV. CONTROL DC 12V VOLUME LEVEL MUTE SOURCE OPT. MUTE LINE IN AU-A220 VOLUME LEVEL MUTE SOURCE OPT. MUTE LINE IN AU-A220 VOLUME LEVEL...
-
Page 18: Specifications
8. SPECIFICATIONS Output Ports 8×12V DC (2-pin Terminal Block) 2×12V DC (4-pin Terminal Block) Control Ports 1×RS-232 (3.5mm) 1×IP Control (RJ45) Baud Rate Up to 115200bps Power Supply 12V/12.5A DC (US/EU standards, CE/FCC/UL certified) ESD Protection Human Body Model: ±8kV (Air Discharge) ±4kV (Contact Discharge) Dimensions 211.5mm×24mm×116.5mm (W×H×D) -
Page 19: Acronyms
9. ACRONYMS ACRONYM COMPLETE TERM Command-Line Interface Graphical User Interface Internet Protocol Local Area Network Personal Computer... - Page 20 CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton, Middlesex, TW17 8BA Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279 Email: sales@cypeurope.com www.cypeurope.com v1.00...
Need help?
Do you have a question about the RAX-PSU-12V and is the answer not in the manual?
Questions and answers