Subscribe to Our Youtube Channel
Related Manuals for LuCell UP-040
Summary of Contents for LuCell UP-040
- Page 1 UP-040 UP-060 Design revolution that empowers the safes users Fire resistant safes User manual...
-
Page 2: Table Of Contents
Contents Safety Precautions Before Use Keypad Overview Keypad Lock mode Security mode Connecting DC Adaptor (UP-060 only) Using battery pack Opening / Closing Door How to use Alarm Changing Password Sound E ect On / O Using ngerprint lock Anchoring Instructions Trouble shooting The safe you purchased is a 'fire resistant safe' that protects valuables against fire. -
Page 3: Safety Precautions
Safety Precautions Safety precautions are to prevent any unexpected risk or damage. Please read before use. - Be carefull when opening and closing door. Finger or objects may get stuck. - Keep away from children. - Do not hit edge of safe to avoid injury. - Safe is heavy. -
Page 4: Keypad Overview
Touch Keypad Fingerprint LCD Display Touch START button Touch Pannel Main Body Power supply (UP-060) Drawer (UP-060) Tray (UP-040) Card/Key holder Shelf Battery compartment Alarm Emergency battery port Memory button for password change Keypad Lock Mode - Press START for more than 3 seconds until “Act” appears. “Act” message signifies activation of keypad lock mode. -
Page 5: Connecting Dc Adaptor (Up-060 Only)
Connecting DC adaptor (UP-060 only) This safe uses DC 12V adaptor as main power supply. Speci cation or design of adaptor is subject to change without pre-notice. Unauthentic adaptor may cause troubles in the system (This is not covered by our warranty) 1. -
Page 6: Using Battery Pack
Using Battery pack Battery is auxiliary power supply. Use the adaptor for the better use of safe Battery pack is located on backside of door. (Emergency battery pack on the side of safe’s door is only for urgent case) Replacing Batteries Replace Batteries immediately when - screen displays “Lo_bAt”... -
Page 7: Opening / Closing Door
Opening / Closing Door 1. Press START button “------“ will be displayed on screen. 2. Input 4~20 digit password. Input factory password “1, 2, 3, 4, 5, 6” for User 1, “5, 6, 7, 8, 9, 0” for User 2(Option). “OPEn”... -
Page 8: Changing Password
Changing Password Safe can be programmed with either 1 or 2 passwords. After having changed the password, please con rm safe is properly working before closing the door. 1. Enter current password and open door. 2. Press white memory button located inside door. “-CodE-“... -
Page 9: Using Ngerprint Lock
Using ngerprint lock Maximum 10 ngerprints can be registered. “Err-04” will be shown on display when ngerprint is not correct or an unauthorized ngerprint attempts access. Registration of ngerprints 1. Push white memory button for 3 seconds until display shows “Set”. 2. -
Page 10: Anchoring Instructions
Anchoring Instructions Anchor bolt must be inserted into oor BEFORE safe is bolted down. 1. Anchor bolts vary according to model. After checking anchor bolt size, drill a hole to a depth of 2 inches (50mm). Refer to chart for appropriate hole size. A (Anchor size) B (Diameter of hole) 1/4”... -
Page 11: Trouble Shooting
Trouble shooting Situation Possible Cause Measures ·Main power error ·Check the adaptor ·Dead battery ·Replace new batteries No response when ·Incorrect insertion of ·Remove batteries and insert START button batteries in the correct polarity pressed ·Keypad lock mode ON ·Press START for 3 seconds to deactivate keypad lock mode ·Circuit error ·Contact Service Centre... - Page 12 Hotline: 6745 6800 email: enq@duro.com.sg...
Need help?
Do you have a question about the UP-040 and is the answer not in the manual?
Questions and answers