Miele SMUL5 Operating Instructions Manual
Cordless stick vacuum cleaner
Hide thumbs
Also See for SMUL5:
- Operating instructions manual (208 pages) ,
- Operating instructions manual (40 pages)
Related Manuals for Miele SMUL5
Summary of Contents for Miele SMUL5
- Page 1 Operating instructions Cordless stick vacuum cleaner AUS, NZ HS19 M.-Nr. 11 579 120...
-
Page 2: Table Of Contents
Contents Warning and Safety instructions ..............Caring for the environment ................11 Guide to the appliance ..................12 Installation and connection ................14 Assembling the vacuum cleaner ................. 14 Connecting the Comfort handle ................14 Connecting the PowerUnit and the suction tube ..........15 Inserting the battery .................... - Page 3 Contents Cleaning and care ..................... 35 Service........................ 35 Contact in case of malfunction ................35 Warranty ......................35 Optional accessories ..................36 Electrical connection ..................37...
-
Page 4: Warning And Safety Instructions
“Installation and connection” chapter as well as the safety instruc- tions and warnings. Miele cannot be held liable for injury or damage caused by non- compliance with these instructions. Keep these operating instructions in a safe place and pass them on to any future owner. - Page 5 Warning and Safety instructions This vacuum cleaner can be used for all normal cleaning of car- pets, rugs and robust hard flooring. This vacuum cleaner is intended for use at altitudes of up to 4000 m above sea level. ...
- Page 6 Repairs and other work by unqualified persons can cause consid- erable danger to users. Miele can only guarantee the safety of the appliance when genu- ine Miele replacement parts are used. Faulty components must only be replaced with genuine Miele replacement parts.
- Page 7 Warning and Safety instructions If the vacuum cleaner is to be stored unused for a long period, the battery should be removed. The supply terminals must not be short-circuited. Cleaning Do not immerse the vacuum cleaner or any accessories supplied with it in water.
- Page 8 Do not vacuum at head height and do not let the suction get any- where near a person's head. Accessories Only use genuine accessories with the “ORIGINAL Miele” logo on the packaging. The manufacturer cannot otherwise guarantee the safety of the product. Safety instructions and warnings for AP01 battery, LG01...
- Page 9 The AP01 battery, the LG01 charger and the LS03 charger cradle are designed for use with the Miele HS19 vacuum cleaner. For safety reasons, the vacuum cleaner must not be used with a battery, char- ger or charger cradle produced by another manufacturer.
- Page 10 To deal with leaking batteries, refer to the Safety Data Sheet (con- tact Miele to request a copy). Correct use Do not drop or throw the AP01 battery. For safety reasons, do not continue to use an AP01 battery which has been damaged.
-
Page 11: Caring For The Environment
Caring for the environment with Miele. Ensure that it presents no Disposal of the packing mater- danger to children while being stored for disposal. The packaging is designed to protect the appliance from damage during Disposing of old batteries transportation. The packaging materials... -
Page 12: Guide To The Appliance
Guide to the appliance... - Page 13 Guide to the appliance a Comfort handle b Release catch for Comfort handle (on the back) c Dust container handle d Dust container with pre-filter, fine dust filter and motor protection filter e PowerUnit with battery connection and connections for Comfort handle, suc- tion tube, Electrobrush and dust container f Release catches for battery (on both sides of the battery) g Charging socket (at the bottom of the battery)
-
Page 14: Installation And Connection
- ergonomic (reduced strain on the Installation and connection wrist) Assembling the vacuum cleaner - convenient cleaning of large surfaces You can assemble the vacuum cleaner The advantages of placing the in 2 different ways. PowerUnit at the top of the vacuum cleaner are as follows: - convenient cleaning underneath fur- niture... -
Page 15: Connecting The Powerunit And The Suction Tube
Press the release catch and remove the Comfort handle by pulling up- wards. Connecting the PowerUnit and the suction tube Depending on how your vacuum cleaner is configured, the suction tube is located either above or below the PowerUnit. ... -
Page 16: Inserting The Battery
Press the release catch to separate Push the battery along the guide lines the individual sections from each until it audibly clicks into place in the other. PowerUnit. Inserting the battery If you want to separate the sections again, press both release catches at ... -
Page 17: Connecting The Electrobrush
Connecting the Electrobrush General battery information Depending on how your vacuum The rechargeable battery is supplied cleaner is configured, you can connect not fully charged. either the PowerUnit connector or the Charge the battery completely before suction tube connector to the Electro- using it for the first time. -
Page 18: Charging The Battery (Without Wall Mounting)
Charging the battery (without wall Charging the battery (with wall mounting) mounting) You can store the vacuum cleaner up- There are 2 ways to store and charge right and charge the battery directly. the vacuum cleaner in the supplied wall bracket. You will need a suitable location near a free power socket for mounting the appliance on the wall. -
Page 19: Wall Mounting
Wall mounting The supplied wall bracket has a mount- ing plate with a bag of screws attached to the back. Attach the mounting plate to the point on the wall where you want the wall mounting to be. Remove the bag of screws. ... -
Page 20: Attaching The Mounting Plate
Attach the mounting plate to the wall. Attaching the mounting plate 2 plugs and 2 T20 TORX screws are Attaching the charging cable to the supplied for attaching the mounting wall bracket plate to the wall. A cable compartment is located on the You will also need a battery-operated underside of the wall bracket. -
Page 21: Connecting The Accessories Holder (If Required)
Connecting the wall bracket Refit the cover and close the cable compartment. Slide the wall bracket down into the mounting plate from above until it Then turn over the wall bracket. audibly clicks into place. Connecting the accessories holder (if required) An accessories holder is supplied for storing the three-piece accessory set... -
Page 22: Battery Charging State Indicator (While Charging)
Battery charging state indicator If the battery has not been used for a (while charging) long time and has run down, it will go into a safe mode. As a result, the bat- The battery charging state is displayed tery charging state indicator will only on the PowerUnit. -
Page 23: Using The Accessories Supplied
Accessory for vacuuming skirting ent option for cleaning carpeted stairs. boards, carved furniture or orna- ments. Miele offers a range of suitable ac- The head can be swivelled to ad- cessories for many special applica- just the angle. tions (see “Optional accessories”). -
Page 24: Electro Compact Handheld Brush (Seb 23)
Electro Compact handheld brush (SEB 23) (depending on model) Follow the flooring manufacturer’s cleaning and care instructions. After the battery has been fully charged once in the PowerUnit, the charger cradle can be used to charge it. Push the battery into the charger cradle until it audibly clicks into place. -
Page 25: Use
The floor covering detection function is activated in the medium and highest Switching on and off power levels. The Electrobrush power output is auto- Pull the charger out of the charging matically set to the optimum level socket on the battery if you have based on the type of flooring –... -
Page 26: Maintenance
Original Miele accessories are available from the Miele Webshop, Miele and your Miele supplier. Original Miele accessories are identified by the “ORIGINAL Miele” logo on the packaging. Lift the dust container upwards to re- move it. The contents of the container can be... - Page 27 Hold the dust container close to the bin to prevent dust from billowing out. Slide the dust container handle along the guide line and down on to the PowerUnit connector from above until Turn the lid of the dust container in it audibly clicks into place.
-
Page 28: Cleaning The Fine Dust Filter
Once it is clean, replace the fine dust Cleaning the fine dust filter filter in its position in the dust con- The fine dust filter is located in the dust tainer. container. Clean the fine dust filter at least once a ... - Page 29 Unlock the motor protection filter by Replace the pre-filter in the dust con- turning it anti-clockwise and lift it up- tainer. wards to remove it. Risk of damage caused by incor- rect cleaning. The pre-filter can become damaged and be less effective as a result.
-
Page 30: Cleaning The Dust Container
Cleaning the dust container Clean the dust container as required. Remove the dust container. Empty the dust container over a bin and lift the pre-filter upwards to re- move it. Clean the dust container using water and mild washing-up liquid. ... -
Page 31: Replacing The Rechargeable Battery
Reassemble the Electrobrush in re- verse order. Replacing the rechargeable battery An original Miele AP01 lithium-ion re- chargeable battery (HX LA) is required. Follow the instructions regarding the handling and disposal of rechargeable batteries found in the following sec- tions: “Warning and safety”, “Caring... -
Page 32: Problem Solving Guide
With the help of the following guide, minor faults in the performance of the appli- ance, some of which may result from incorrect operation, can be remedied without contacting Miele. This will save you time and money because you won't need a service call. - Page 33 Charge the battery exactly as described in these operating instructions (see “Installation and con- nection” – “Charging the battery”). An original Miele battery has not been inserted. Insert an original Miele AP01 lithium-ion re- chargeable battery (HX LA). The charger is still plugged in.
-
Page 34: Error Messages
Middle and top lights “Battery not recognised” error flash quickly Insert an original Miele AP01 lithium-ion re- chargeable battery (HX LA). Top light flashes quickly “Comfort handle not recognised” error Remove the Comfort handle and reconnect it (see “Installation and connection”... -
Page 35: Cleaning And Care
Miele. Switch the vacuum cleaner off before Contact information for Miele can be cleaning it. Use the On/Off switch on found at the end of this document. the Comfort handle to do this. -
Page 36: Optional Accessories
Purchasing accessories Crevice nozzle, 560 mm (SFD 20) Original Miele accessories are available Flexible crevice nozzle for vacuuming from the Miele webshop, the Miele Cus- hard to reach places. tomer Service Department and from Additional AP01 battery (HX LA) your Miele dealer. -
Page 37: Electrical Connection
Electrical connection All work should be carried out by a suit- ably qualified and competent person in strict accordance with national and local safety regulations. The voltage and rated load are given on the data plate located underneath the vacuum cleaner. - Page 40 Miele Experience Centre South Melbourne: Auckland: 206-210 Coventry Street 8 College Hill South Melbourne, VIC 3205 Freemans Bay, Auckland 1011 Miele Experience Centre and Office Sydney: Miele Experience Centre Wellington: 3 Skyline Place Frenchs Forest, NSW 2086 183 Featherston Street...