Advertisement
Quick Links
SHPE1000 Series SaltDogg
Electric Drive Poly Hopper
Spreader
1.0 cubic yard
U.S. PATENT 9,562,333
Table of Contents
General Information .....................................................................1
Safety Precautions .......................................................................1
Warranty Information ...................................................................2
Installation Instructions ............................................................ 2-4
Spreader Operation .....................................................................5
Spreader Maintenance .................................................................5
Repair Parts & Drawings .........................................................6-10
General Information
Spreader models:
• SHPE1000- spreader with standard length chute
• SHPE1000X- spreader with extended length chute
Overall Length: 72 inches
Overall Width: 48 inches
Overall Height: (installed): 34 inches
Empty Weight: 343 lbs. (standard chute), 347 lbs. (extended chute)
Capacity Struck: 1.0 cu. yd.
Average Installation Time: 3 hrs.
Vehicle Requirements
• 1/2 or 3/4 ton pick-up truck.
• 135 AMP or higher alternator is recommended.
CAUTION
Do not overload vehicle beyond the vehicle's GVWR or GAWR.
Check vehicle's load rating certification sticker for maximum
vehicle capacity.
Materials Recommended to Spread
Average Material Weights
Materials to use
Fine Salt-Dry
Coarse Salt-Dry
Sand/Salt up to 50/50 Mix-Dry
Note: To calculate the total spreader weight (including ice
control material), add the empty spreader weight plus the ice
control material and spreader accessories.
Installation Instructions
®
Weight (pounds per cubic yard)
2,250
1,431
2,700
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • saltdogg.com
SHPE1000 SALTDOGG
INFORMATION
This warranty replaces all previous warranties and no
employee of this company is authorized to extend addi-
tional warranties, or agreements, or implications
not explicitly covered herein.
Buyers Products Company warrants all parts of the
product to be free from defects in material and workman-
ship for a period of two (2) years. Parts must be properly
installed and used under normal conditions. Normal wear
is excluded.
Any part, which has been altered, including modifica-
tions, misuse, accident, or lack of maintenance will not
be considered under this warranty.
The sole responsibility of Buyers Products Company
under this warranty is limited to repairing or replacing any
part(s), which are returned, prepaid, 30
days after such defect is discovered, and returned part(s)
are found to be defective by Buyers Products Company.
Authorization from Buyers Products Company must be
obtained before returning any part. The following infor-
mation must accompany defective parts returned
to Buyers Products Company: RMA #, spreader model,
serial number, date installed, and distributor from whom
purchased.
Buyers Products Company shall not be liable for damage
arising out of failure of any unit to operate properly, or
failure, or delay in work, or for any consequential dam-
ages. No charges for transportation or labor performed
on any part will be allowed under this warranty.
1
9049 Tyler Blvd. • Mentor, Ohio 44060
SPREADER WARRANTY
®
—continued inside
Advertisement
Related Manuals for Buyers Salt Dogg SHPE1000 Series
Summary of Contents for Buyers Salt Dogg SHPE1000 Series
- Page 1 30 days after such defect is discovered, and returned part(s) Do not overload vehicle beyond the vehicle’s GVWR or GAWR. are found to be defective by Buyers Products Company. Check vehicle's load rating certification sticker for maximum vehicle capacity.
- Page 2 Safety Precautions F. Attach the Chute Assembly to the spreader. First, hook the Chute to the spreader by openings in the Chute’s handle. WARNING Fig. 2 Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided.
- Page 3 Fig. 4 2" x 6" WARNING Do not drill holes into fuel tanks, fuel lines, through electrical FIT TO BOX 6" wiring, etc that may be damaged by drilling. 2. Install Control Box & Vehicle Wiring Harness (Fig. 7). NOTE: THIS IS A WIRE GROUND ELECTRICAL SYSTEM! NO 2"...
- Page 4 3001379 Fig. 7 CB120PB BATTERY POSITIVE BATTERY NEGATIVE 3035933 3006724 3014199 Thoroughly clean battery terminals. Make sure battery full speed for 2 seconds, then slow down to dialed speed. terminals have no tarnish or corrosion. 5. To activate the vibrator press the vibrator switch ON. Vibrator DO NOT CONNECT WIRE HARNESS TO DAMAGED switch will illuminate.
- Page 5 to expose more of rear (closer to truck's rear end) portion of 3. Lubricate bearing every 7-10 hours of operation using general discharge opening to increase flow without overloading auger automotive grease. gear motor. (Fig 8) 4. Inspect terminals/connectors every time you disconnect IMPORTANT! -Always turn off power before making any spreader from wire harness.
- Page 6 Repair Parts - Standard Chute Assembly Repair Parts - Extended Chute Assembly Bill of Materials Bill of Materials ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 3025063 CHUTE POLY, SHPE STD. LENGTH 3007526 CHUTE POLY. EXT. LENGTH 3033665 BRACKET WELDMENT, CHUTE 3006833 GEAR MOTOR 12 VDC.
- Page 7 Repair Parts-Hopper Assembly Bill of Materials ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 3022973 HOPPER POLY 1 CU YA FWL025050006SS WASHER, 1/4 IN. SPRING LOCK SST 3024289 TROUGH ASSEMBLY, SHPE FCS025020075SS SCREW, CAP 1/4-20 X 3/4 SST 3022230 CROSS MEMBER 3007522...
- Page 8 9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Repair Parts- Trough Repair Parts- Spreader Bill of Materials ITEM PART NO. QTY. DESCRIPTION 3024290 TROUGH WELDMENT SHPE1500 3007000 GASKET, FELT BEARING 3018919 BEARING, 2-HOLE FLANGED 1"...