Swim 'n' rinse compact shower, retail chrome with horizontal holder, grey with angled/horizontal holder, chrome with angled/horizontal holder (17 pages)
Summary of Contents for Whale INSTANT MATCH PREMIUM SDP303T
Page 1
Installation guidelines for Models ® SDP303T Whale INSTANT MATCH PREMIUM Kit WITH For Installation Videos and Electric Shower Kits, please refer to the Whale website: www.whalepumps.com/psd Technical Helpline: 0845 0694 253 www.youtube.com/WhaleHealthcare 300 000 Please leave this booklet with the end user...
7 How do I register my warranty? Please complete and return the warranty registration form supplied with your pump, www.whalepumps.com/psd or complete the online form at: 0845 0694 253 info@whalepumps.com www.whalepumps.com/psd Whale, 2 Enterprise Road, Bangor, Co. Down, @Whalecare BT19 7TA, N.Ireland...
Thank you for purchasing this Instant Match Premium product. ® Whale is the market leader in pumped shower drainage kits. These kits have the reputation of working reliably for many years without requiring maintenance. The front cover shows the product installation in an apartment with the components in a concealed access.
umbing of the Waste Pipe Index User warnings End user help Principles of operation Plumbing specification Plumbing gulley Plumbing of waste pipe Installation Transformer settings Swapping pump & transformer on backplate Safety warning Installation testing and repair EU declaration of conformity Statement of limited warranty Specification List of parts included in the kit...
FALL WHERE THE PIPE LENGTH IS GREATER THAN 1M. WARNING IF LESS THAN 1M USE 22MM PIPE ® • The Whale pump is IP45 compliant. Locate pump in accordance with BS7671: 2008 Part 7 (17th Edition). The pump may be installed in bathroom zones 1, 2 or 3.
Fig 1.2 • Rotate the pump head if necessary. Loosen clamping ring screw, rotate and retighten as shown. See Fig 1.2 • Before commissioning the shower and running water through the system, ensure that the shower area and gulley are completely free of building debris, especially tile grout, screed material and latex.
32mm (1 ") McAlpine examples and the McAlpine catalogue for other variants. Use with a Macerator Pump ® • Discharge from the Whale pump must go into the top of the macerator box. Do not use the bottom entries. 32mm ") 1 /4 See Fig 1.6...
lumbing of the Waste Pipe Installation 1. Plumbing drainage pipe and hot and cold supplies • Run 22mm pipe from gulley to pump inlet (max 2m). • Only slow radius or pre-formed bends to be used. • Sensor provided with 1m of cable. Additional cable purchased separately (part number SDS281T).
Page 9
3. Mounting your pump to the wall • Mark the hole centres through unit backplate. • Drill holes in wall and fit wall plugs (if necessary). Use 6mm masonry bit. • Secure the backplate to the wall using supplied screws. •...
Page 10
® 5. Plumbing Sika Sensors • Plumb Sika flow sensors to hot and cold supplies with the arrow pointing in the direction of the water flow. • Do not overtighten the plumbing fittings connected to the Sika flow sensors as doing so may cause leaks. 6.
Page 11
Transformer settings (see page 13). • Refit the hatch and tighten the screws to make the transformer water resistant. ® The Whale Instant Match Premium transformer includes Activelink diagnostics to aid installation: On the transformer are two indicator LEDs •...
Page 12
8. Regulate your shower flow rate • Where there is a risk of the flow rate exceeding 12 ltrs per min, the flow regulator must be fitted. • Fit the internal flow regulator to the shower hose as shown between the mixer bar valve and the shower hose.
• External components for service are jumper settings only. • Where there is damage to the transformer or cabling, contact your Whale distributor for a replacement. • Do not connect mains power to the pump as this will cause permanent damage and will result in an electrical hazard.
Installation Testing & Repair CHECK TRICUSPID VALVE - Remove the tricuspid valve holder screwed onto the pump discharge. Remove the rubber valve and assess its condition. If it is worn or stiff then change The pump system is designed not to require maintenance. and re-test.
- Maximum Head & Lift: 1.5m Munster Simms Engineering Limited, Bangor, Northern Ireland trading as - IP45 Whale. Whale’s policy is one of continuous improvement and we reserve the right to change specifications without prior notice. Illustrations are for Transformer guidance purposes only.
umbing of the Waste Pipe List of Parts included in the kit Item Part No. Shower Drain Pump SDS021T Transformer Instant Match Premium SDS233T Pump Cover base 755.610 Pump Cover (for mixer) SDS261T Wet Floor Gulley (vinyl floors) 755.274 Tray Gulley (50mm) 755.108 Sika Sensor SDS263T...
Page 19
Pump Base Standoffs Where pipe runs make installation of the pump base difficult we recommend the use of a Space - Plug (Available from SCREWFIX Version 30-50mm shown below)
INSTANT MATCH Kit Fault Diagnosis What is the fault? Pump will not start Pump will not stop The transformer allows the pump to Ensure power is connected and switched on. over-run for up to 60 seconds. If the pump continues to run after this Press the TEST button on top of the transformer.
Page 21
Pump does not pump properly Ensure that the gulley is not blocked and that fittings are pushed home and airtight. Re-test and if pump does not pump properly, remove inlet coupling and press the test button on the transformer, or run the shower into the sink to run the pump.
Plumbing Specification WASTE PIPE FORMED BEND Maximum pipe length is 2m from gulley to pump. Pipe from gulley to pump must be in 22mm. 1M (MAX) MIN 1:40 FALL WARNING 22MM DIA PIPE USE ONLY 22MM PIPE ON THE 0.5 M GULLEY PUMP OUTLET (MAX)
Page 23
Pump - SDS021T 310mm 255mm 150mm TRICUSPID VALVE Contact the Technical Helpline If you need further assistance: 0845 0694 253...