Sealey CP20VRP Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
polisher.
Familiarise yourself with the application, limitations and potential hazards of the polisher.
9
WARNING! Disconnect from the mains power and ensure that the pad is at a complete standstill before changing accessories,
‰
servicing or performing any maintenance.
Maintain the polisher in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
WARNING! Keep all guards and holding screws in place, tight and in good working order.
‰
Check regularly for damaged parts. A guard or any other part that is damaged must be repaired/replaced before the polisher is next
9
used.
Use the polisher in a suitable work area and keep the area clean and tidy and free from unrelated materials. Ensure that there is
9
adequate lighting.
Keep the polisher clean for best and safest performance.
9
Before each use check all attachments for condition. If worn or damaged replace immediately.
9
Ensure that there are no flammable materials near the work area.
9
WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
‰
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Avoid unintentional starting.
9
DO NOT use the polisher for any purpose other than that for which it is designed.
8
DO NOT operate the polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT switch the polisher on until the head is in contact with the panel and switch the unit off before removing the head from the
8
panel.
DO NOT use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
8
DO NOT get the polisher wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the polisher.
8
DO NOT operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT leave the polisher operating unattended.
8
DO NOT carry the polisher with your finger on the power switch.
8
DO NOT pull the cord from the power supply.
8
Use a qualified person to maintain the polisher.
9
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
9
2. INTRODUCTION
Digital display and variable speed control from 500-3000rpm. Features a slide button on/off switch allowing for a smooth comfortable main
handle grip. Spindle lock for fast and easy pad changes. Double injection composite housing with rubber grip for added comfort. Supplied with
Ø150mm backing pad and side handle. Requires Model No's CP20VBP, CP20VBP2 or CP20VBP4 20V Battery and Model No. CP20VMC
Mains Charger.
3. SPECIFICATION
Model No:..............................................................CP20VRP
Battery: ................................................. 20V 2Ah - 6Ah Li-ion
Consumable Parts: ......................................PTC/150VA/M14
Free Speed: ...................................................... 500-3000rpm
Noise Power/Pressure: ........................................ 85/74dB(A)
Pad Size: ................................................................ Ø150mm
Thread Size: ....................................................... M14 x 2mm
Vibration/Uncertainty: ........................................ 8.27/1.5 m/s²
© Jack Sealey Limited
Ø150MM CORDLESS ROTARY POLISHER 20V
- BODY ONLY
MODEL NO:
Wear protective Wear protective
gloves clothing
Original Language Version
CP20VRP
Wear ear Wear a mask
protection
CP20VRP Issue 1 06/05/20