1. Manuals
  2. Brands
  3. Zico Manuals
  4. Data Loggers
  5. ZI-9530
  6. Manual

Zico ZI-9530 Manual

Temperature and humidity data logger
Hide thumbs Also See for ZI-9530:
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
ZI-9530
Temperature and Humidity data logger Manual
Product overview:
1. Sensor
2. Alarm indicator, red/green LED inside.
: green LED flashing，
3. Electronic function key
4. Mechanical switch, hold down the switch, then pull out the shell.
5. USB protecting hood. Connect PC software
then you can setting up the data logger.
Replace battery
Simple start:
①Check the battery indicator
②Connect the USB data logger to the Windows PC. The first time using, according to the
computer instructions, install the system's own driver. Similar to A new U disk.
③Setting the data logger. Please check the software CD，use the PC software setting the data
logger. For more information, please refer to the PC software help document.
④Recording and download data.
First step：
Open the software. Then open the setting window.
www.zicotech.com
: Red LED flashing.
Hold down the switch,
then pull out the shell.
is normal.
CR2450
Battery

Advertisement

Table of Contents
loading

Related Manuals for Zico ZI-9530

Summary of Contents for Zico ZI-9530

  • Page 1 ZI-9530 Temperature and Humidity data logger Manual Product overview: 1. Sensor 2. Alarm indicator, red/green LED inside. : green LED flashing， : Red LED flashing. 3. Electronic function key 4. Mechanical switch, hold down the switch, then pull out the shell.

  • Page 2: Second Step

    Second step: refer to the picture. Third step: After Setting Long Press "Manual"mode Waiting start Recording...

  • Page 3: Record Time

    Fourth step: After recording some data, you can use the PC software download data. Sample rate is 1minute, 10 minutes is ten data. Sample rate & Record time Sample rate Record time Sample rate Record time /min /day /min /day 13.9 111.2 27.8...
  • Page 4 Display: ①...Alarm indicator ②... Battery indicator ③... Record indicator ④... Humidity unit ⑤... Humidity reading ⑥...Temperature unit ⑦...Temperature reading ⑧...Function indicator Buttons: ① down key ② replace battery ③ enter key 1. Alarm indicator Measurement values are within programmed limits. Green LED is flashing. Measurement exceeded the programmed limits.

  • Page 5: Recording Indicators

    3. Recording indicators The current state of the recording is indicated by the following symbols: Recording paused Recording stopped Recording started Appear after setting State 1: long press enter The logger is in the “Manual ” mode, but the start key has not been not pressed yet.

  • Page 6: Function Menu

    Function Menu If the logger is not recording, only Start Recording is available. Press the button to enter the function menu and to display humidity or air pressure, and select the menu functions. To activate a user menu function press the button and hold it for three seconds.
  • Page 7 short/long press enter 5.Min 6.Short press button switch Shows the lowest reading since start of recording. short/long press enter Generating a PDF-File As soon as the logger is connected to a USB-slot, a PDF file with all recorded data in chart and an overview of alarms is generated automatically.
  • Page 8 -30~60℃ condition model type Data memory Sample rate ZI-9530 Temperature and Humidity 20010 1min~24h Remark: CR2450 battery performance is optimal in room temperature. Battery life cycle will reduce at low temperature (-18℃). If the device is to be used to record in extremely low temperature, it is advised to take measures to reduce power consumption to prolong operation time.
  • Page 9 Restore Default factory firmware Remove the battery, in the following order: 1. Hold down the button (until power on) ; connect to the computer USB, the green LED light up. 2. Waiting for 2 minutes, computer will identify the instrument USB disk. Delete all data 1.

Table of Contents