Related Manuals for Kargo Master 4A84L
Summary of Contents for Kargo Master 4A84L
- Page 1 Instruction Guide 4A84L Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com 20210629R3 DATE: ________________...
-
Page 2: Table Of Contents
Examples of Ladder Clamps Firmly Against Ladder Rungs ................12 Before You Begin Read all instructions prior to assembling or installing any Kargo Master product. Always locate your installation locations prior to performing any work. DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF. -
Page 3: Parts
Instructions – 4A84L Parts For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2... -
Page 4: Hardware
Instructions – 4A84L Hardware For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3... - Page 5 Instructions – 4A84L Hardware (Continued) For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4...
-
Page 6: Step 1 - Attach End Stops To Bow
Instructions – 4A84L DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF Step 1 – Attach End Stops to Bow If installing driver side ladder rack, skip this step. Using two 5/16” carriage bolts, 5/16” washers and 5/16” lock nuts, bolt end stop to bow as shown. Be sure carriage bolt is inserted downward. -
Page 7: Step 3 - Install Side Tube
Instructions – 4A84L Step 3 – Install Side Tube Place side tube assembly on top of bows. Have the bend towards the front and to the outside of the vehicle as shown. In some applications, it is easier to assemble rack on top of vehicle. -
Page 8: Step 4 - Install Hanger Bracket
Instructions – 4A84L Step 4 – Install Hanger Bracket Using two 5/16” x 2” carriage bolts, 5/16” flat washers and 5/16” lock nuts, bolt the hanger bracket to the side tube as shown. Be sure to have the bracket flange towards the inside of the bows. - Page 9 Instructions – 4A84L Insert clamp tube with bushings into L-bracket and hanger bracket installed in Step 3. Be sure flanges on bushing are toward each other and are oriented toward inside so they CANNOT fall out, as shown. Insert clamp tube into both plastic bushings.
-
Page 10: Step 6 - Install Latch Assembly
Instructions – 4A84L Step 6 – Install Latch Assembly Using a 5/16” x 2” carriage bolt, 5/16” flat washer and 5/16” lock nut, bolt latch to the rear of the mount tube that was installed in Step 3. TIGHTEN. -
Page 11: Step 8 - Install Ladder Hook Bracket To Bow
Instructions – 4A84L Step 8 – Install Ladder Hook Bracket to Bow Using two 3/8” x 1” carriage bolts, 3/8” flat washers and 3/8” lock nuts, bolt ladder hook bracket to the bow in the orientation shown. Be sure the bracket is square to the bow. - Page 12 Instructions – 4A84L Feet can be installed outward as shown below or reverse depending on the roof mounting. Using 3/8” x 3/4" hex head bolts, 3/8” lock washers and 3/8” flat washers, bolt foot to cross member. Snug tighten, but allow movement.
-
Page 13: Angle Pad Orientations And Locations
Instructions – 4A84L Angle Pad Orientations and Locations Rear- Front-Facing Facing Clamp Mechanism Orientation and Angled Pad Positions Rear- Facing Examples of Ladder Clamps Firmly Against Ladder Rungs Be sure to position the ladder hook in a way so the hook clamps the ladder tight into place. A tight fit ensures the ladder cannot fall off the rack.