Advertisement
Setting up the TV set for the fi rst time
1
Fitting the stand
TV panel must be facing downwards.
For the stand installation, there is one type of screw
provided as shown below.
To complete the stand installation you will require a
cross head screw driver.
Place the TV set on a fl at and clean surface with the
panel facing downwards to avoid damage.
1
4 x
Place the TV set on a fl at and clean surface with
the panel facing downwards to avoid damage.
Used for attaching the stand
to the TV set (fi g.2)
3
Connecting your set
Outdoor Digital
1.
TV Aerial
2.
1) Connect the TV to your power socket.
2) If you wish to use the TV to receive Freeview/Saorview channels,
connect the RF input from the TV to your outdoor Digital TV aerial.
If you do not wish to receive Freeview/Saorview, skip this step.
4
First time installation
1
1. Languages
Select your preferred on screen display language. This will change the language in
which the menus and associated information is displayed in. When set up has been
completed, this can be changed by selecting Menu > Settings > Language
4
4. Environment of Use
Home Mode: For normal use, by default it is set to a power saving mode which re-
duces the energy used by up to 25% (by reducing the power to the LED/LCD panel).
This can be changed in the picture mode settings.
NOTE: In Home Mode, the TV will switch itself to the standby mode after 4 hours in
the event that the buttons on the remote control or TV set are not used.
Store Mode: For store display use. The picture is adjusted to optimum settings. The
store demonstration will appear on the screen automatically after two minutes.
Back/Shortest
Front/Longest
2
When the stand feet are installed correctly the
stand feet will be longest at the front of the TV
and shortest at the back with the feet pointing
away from each other.
Button layout
1
Volume up and menu right
1
2
2
Volume down and menu left
3
Programme/Channel up and menu up
3
4
4
Programme/Channel down and menu down
5
Displays Menu/OSD
5
6
6
Displays the input source menu
Standby Power On/Off
7
7
2
2. Country Selection
Select the correct fl ag for the country in which the set will be used in. This will enable
the set to correctly install the functions applicable in the country of use.
5
5. TV Installation – Audio.
Depending on how you use / install your TV, select the appropriate setting. The sound
settings on the TV will adjust to suit the type of installation.
3
4
1
2
4 x
3
When the stand/feet are in the correct position, secure
the feet to the underside of the TV set using 4 screws
provided.
To receive Freeview channels, in particular Freeview HD
channels, you will need a Digital TV aerial and be in a good
Freeview coverage area. You can check coverage for your
postcode at www.freeview.co.uk.
Please note that any Freeview HD channels found during
tuning will be placed in channel positions above 100.
For example, 101 (BBC1 HD) 102 (BBC2 HD) etc.
3
3. Network setup
You can connect the TV to your broadband router or wire-
less network in order to take advantage of the Smart functions. If you connect the
TV to your router using an Ethernet cable (recommended) this step will be skipped.
Follow the on screen prompts to connect to your wireless network. You can set up
the Network connection later in the network menu.
6
6. Default Source
Select the source which you use the most. If Digital TV (Freeview) is chosen, then at
the next step, the set will tune in and default to Digital TV (Freeview). If one of the
other sources is selected, then the set will not tune in at this stage and default to
that input. If it is required to tune the set in later, this can be achieved by selecting
Menu > Channels
2
Installing batteries
Insert the batteries supplied into the remote control and press the standby button
to power on the TV.
Sky remote code
If you wish to use your Sky+/HD+ remote to
operate the TV's basic functions, you will
need a Sky remote control (Revision 9 or
later) and you will need to program it with
the code 2134.
If you wish to use your Sky Q remote to
operate the TV's basic functions, you will
need to program it with the code 4170.
Connectivity
ARC
A
B
D
E
C
F
G
A
I
Ethernet/LAN*
Network connection
SAT IN
J
B
Digital Audio
Digital Optical Audio Output
RF in
C
K
USB 2.0
2 x USB port 2.0
HDMI 3**
D
L
HDMI 1
HDMI input
USB 3.0
E
M
HDMI 2
HDMI input (ARC)
CI card in
F
N
YPbPr
HD input (YPbPr)
SD
O
G
AV IN
Audio/Video input
Earphones
Mini SCART
Mini SCART input
H
* The Ethernet/LAN port is used for Freeview HD services and smart functions.
O
N
M
L
K
J
H
I
Satellite input
RF / TV aerial input
HDMI input
USB port 3.0
Common interface module
SD card input
Earphone input
Advertisement
