Advertisement
3.
INTRODUCTION & SPECIFICATION
GS/TUV approved quality long stroke air hammer supplied in carry case. Kit also includes spare retainer spring, long blade panel cutter, special
panel cutter, panel cutter, muffler tail pipe remover, cold chisel, air hose connector and air tool lubricating oil.
SPECIFICATION
Chisel Shank . . . .0.401” Parker Taper
Speed . . . . . . . . . . . . . . . . . .3500bpm
Stroke . . . . . . . . . . . . . . . . . . . .20mm
4.
OPERATING INSTRUCTIONS
Note: Numbers in brackets refer to item numbers in the parts list.
The air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use. Ensure you read, understand and
follow the safety instructions in Section 1.
4.1.
Attach the retaining spring (17) by screwing it onto the Cylinder (16).
4.2.
Insert the chisel using the hooked end of the spring to hold the chisel in place.
4.3.
Attached the tool to the air supply (see Section 2).
4.4.
To operate the hammer, squeeze the trigger (6). The air regulator (5) may be used as a means of throttle control.
5.
MAINTENANCE
WARNING! Disconnect the hammer from the air supply before changing chisels, servicing or performing any maintenance.
p
5.1.
Keep the hammer oiled for optimum performance.
Lubricate with a good grade of air tool oil such as Sealey ATO/500 or ATO/1000. If there is no oiler in the air system then a teaspoon of
oil can be poured into the air inlet of the hammer, or into the hose at the nearest connection to the air supply. Then run the hammer for
a short time.
Note: The following external factors may cause loss of power and effect hammer performance:
The air supply
Reduced compressor output, excessive drain on the air line, moisture or restrictions in air pipes or the use of hose connectors
having too small a bore. Correct as necessary.
The hammer
Grit or gum deposits in the tool. Correct by cleaning the air strainer and flushing out the tool with gum solvent oil or an equal mixture of
SAE No.10 oil and kerosene.
If, despite taking action as above, the tool function is still impaired, contact your local Sealey service agent.
6.
PARTS LIST
7.
DECLARATION OF CONFORMITY
Declaration of Conformity
LONG STROKE AIR HAMMER
Model SA11/S
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
Operating Pressure . . . . . . . . . . .90psi
Air Consumption . . . . . . . . . . . . .4cfm
Air Inlet . . . . . . . . . . . . . . . . . .1/4”BSP
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Tools.
01284 757500
Weight . . . . . . . . . . . . . . . . . . . .1.5kg
Vibration . . . . . . . . . . . . . . . . . .18m/s
Noise Level . . . . . . . . . . . . .99.9dB(A)
Item
Part No.
1
SA11R/01
2
SA11R/02
3
SA11R/03
4
SA11R/04
5
SA11R/05
6
SA11R/06
8
SA11R/08
9
SA11R/09
10
SA11R/10
11
SA11R/11
12
SA11R/12
15
SA11R/15
16
SA11R/16
17
SA11R/17
Issue No:
Date Issued: 091101
12th November 2001
01284 703534
E-mail: sales@sealey.co.uk
2
Description
Housing
Pin
Ball Seat
0-ring
Air Regulator
Trigger
Valve Stem
Bushing
Spring
Air Inlet
Valve Case
Piston
Cylinder
Spring
1
SA11/S - 1 - 091101
Advertisement
