Advertisement
2. INTRODUCTION
Powerful, lightweight cordless impact wrench. Durable double injection composite housing with soft grip for added comfort. Produces torque of
up to 700Nm. Brushless motor, which gives an improved performance and requires less maintenance than the brushed equivalent, giving you a
more efficient, longer lasting tool. Variable speed trigger switch for easy control. Forward, reverse and trigger-lock. Fitted with electronic brake.
Requires compatible 20V battery and mains charger, sold separately.
3. SPECIFICATION
Model No...................................................................... CP20VPIW
Battery ............................ 20V 2Ah - 6Ah Lithium-ion (not included)
Consumable parts:
CP20VBP2 - 2Ah Battery, CP20VBP4 - 4Ah Battery,
CP20VBP6 - 6Ah Battery
Drive ........................................................................... 1/2"Sq Drive
Impact rate .................................................................... 0-3250bpm
Max. torque ..........................................................................700Nm
Noise power/pressure ................................................. 94/105dB(A)
No-load speed ............................................................... 0-2750rpm
Replacement parts .........CP20VMC - Mains Charger (not included)
Vibration/uncertainty ..................................................29.89/1.5m/s²
4. OPERATION
4.1.
USING THE WRENCH
4.2.
Fit the socket to the wrench by snapping it onto the square drive. Note: Use only impact grade sockets.
4.3.
Fit the battery pack to the wrench by aligning the tongue on the battery with the groove in the housing and slide into place.
Ensure that the battery pack is firmly located, A click will be heard when it has locked into position.
4.4.
Select the required direction of rotation. To change direction, turn
change the direction of rotation whilst trigger is depressed.
4.5.
Speed can be controlled by selecting High or Low buttons on base and by varying the finger pressure on the trigger.
Initial pressure will switch on the work light.
4.6.
4.6.
When tightening, take care not to over-torque small fixings.
When tightening, take care not to over-torque small fixi
Note: On critical fixings always check the torque with a torque wrench according to the product or vehicle manufacturer's guidelines.
5. MAINTENANCE
WARNING: Always disconnect the battery before carrying out any inspection, maintenance or cleaning.
‰
5.1.
GENERAL INSPECTION
5.1.1.
Regularly check that all the fixing screws are tight. Repairs should be carried out by an authorised service centre.
5.2.
CLEANING
WARNING: Always wear protective equipment including eye protection
‰
and gloves when cleaning this tool.
5.2.1.
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device's service life.
5.2.2.
Clean the body of your machine with a soft brush, or dry cloth.
5.2.3.
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is recommended.
5.2.4.
Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it.
5.2.5.
If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
5.3.
LUBRICATION
5.3.1.
Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant.
5.4.
STORAGE
5.4.1.
Store this tool carefully in a secure, dry place out of the reach of children.
WARNING! – Risk of Hand Arm Vibration Injury.
‰
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 29.890m/s²
Uncertainty value (k): 1.5m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures
can be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm
and dry and maintain good blood circulation in fingers etc.
© Jack Sealey Limited
change direction, turn the direction control (fig.1) to the left or right. DO NOT attempt to
Original Language Version
fig.1
CP20VPIW Issue 2 (2,3) 10/06/21
Advertisement
