Advertisement
JA-160PC (90) PIR motion BUS detector with a 90° verification camera
are sent from the internal memory to the control panel. Then the behaviour
is the same as with an instant reaction (11 photos maximum).
Warning: When the Device autobypass / 3rd alarm is enabled (located
in Settings/Parameters), then taking photos is blocked after the 3rd alarm.
During each alarm the detector can be triggered up to three times. This way,
the number of taken and transferred photos can be tripled (18/24 photos).
Applies to Instant/Delayed reactions.
Installation recommendations, cautions
Several JA-160PC (90) detectors can be installed in the system. However,
triggering several detectors at the same time will extend the transmission
time of photos to the control panel and to MyJABLOTRON. Complete
transmission can take a few minutes.
In order to take a photo using a PG output, use the F-Link software and
set the Impulse parameter in the PG outputs / Function menu to a time
of at least 1 min. The PIR is limited to taking 1 requested photo by PG status
per minute.
The number of pre-alarm photos taken by a PG output is limited
to 40 photos/day/control panel. The photo counter is reset at 00:00 hrs.
Alarm photos and photos requested in MyJABLOTRON have no limitation.
In the MyJABLOTRON Photo gallery / Sending notifications and
in J-Link software all users have access to the photos from all the system
sections.
Installation in the corner of a room requires more attention during testing
due to possible reflection of flash in the photographed scene (especially
in the dark).
Detection characteristics
PIR detector has a 90°/12 m coverage – see picture below. The detection
characteristics of the PIR part has no influence on the camera part
of the detector. The lens cannot be changed for other types. The camera has
a viewing angle of 90°, the camera flash has a range of 3 m.
Side view
Saving and browsing the pictures
Every photo is taken twice: the first in low resolution (LQ = 320x240
pixels), the second with high resolution (HQ = 640x480 pixels).
All of the exposures are saved into the independent folders Foto_LQ
and Foto_HQ on the Micro SD card. When the card's capacity is full,
the oldest photos will be replaced by new ones. Photos saved
on the micro SD card can be browsed in a photo browser on a PC.
Note: Some antivirus software may write their own data on the Micro SD
card. The detector will automatically format the SD card marked this way.
SD card formatting erases all data which has been saved. For more
information about formatting see Formatting the Micro SD card.
Photos are sent to the control panel in LQ. You can browse through these
images in F-Link and J-Link software event memory by clicking
on an event called New image. Photos are displayed in LQ, if you click
on Detail you can get second-exposure pictures (HQ). Images can
be searched and browsed by a file manager or picture browser. In order
to display the photos this way it is necessary to start F-Link (J-link) software,
be logged into the control panel as a service technician or Administrator and
then load the control panel memory. Disc: Flexi_log /Foto. Here are all
the photos which have been sent to the control panel (LQ) and photos which
have been requested in Detail (HQ).
Transfer photos to MyJABLOTRON
When the SIM card supplied by a device manufacturer (distributor)
is used and the customer uses MyJABLOTRON services, then the customer
has direct access to the photos from this service. Parameter settings
of the transfer of pictures are done during the panel registration.
All the photos are delivered and visible in MyJABLOTRON. Every single
photo can be requested in HQ resolution.
There you can also choose telephone numbers (for SMS) or e-mail
addresses which will receive a message when a new picture is taken.
MyJABLOTRON can request a new picture without PG output activation (see
Installation recommendations, cautions).
WARNING: This detector allows you to take photos by PG output reaction
or from MyJABLOTRON even when the system is unset. The manufacturer
strictly warns the user that the detector has to be used within the limits given
JA-160PC (90) PIR motion BUS detector with a 90° verification camera
by particular laws or norms, especially laws about the protection of personal
privacy.
The use of the detector is also subject to regulations on the protection
of personal data. The manufacturer recommends the users to familiarize
themselves with these regulations as well as with the regulations governing
the operation of CCTV before the use of the detector. Furthermore,
the manufacturer recommends the users to familiarize themselves with
General Terms and Conditions of Cloud JABLOTRON and with Privacy
Policy (https://gdpr.jablotron.cz/).
According to these regulations users have an obligation to ensure
the approval of persons in range of the detector during the acquisition
of video recordings or the obligation to indicate the image capture area
by information tables.
The detector is supplied with a formatted Micro SD card (12). The yellow
indication LED (11) is turned off in normal detector mode. Slow LED flashing
indicates that the card was removed while data was being written on it,
or it has been changed for another SD card. The detector will work normally
with a new SD card only if the detector performs a card formatting.
Formatting is started by pressing the tamper contact (14). The formatting
procedure is indicated by quick flashing of the yellow LED indicator (11).
During this process all photos on the SD card will be erased, however,
a back-up of the photos is in the event memory log.
The detector monitors its own batteries and when they are depleted,
it will inform you about this with a brief flash of the LED indicator when
the detector is triggered. This information is also delivered to the control
panel. We recommend changing the batteries within two weeks from
the moment the low battery indication starts. After replacing the batteries,
the detector needs up to 3 minutes to stabilize (the red LED indicator is lit
up). The batteries should be replaced by a service technician with the control
panel in Service mode. Always replace both batteries for new ones.
Top view
Note: To ensure a proper functionality of the detector we recommend
using batteries supplied by Jablotron distributors (BAT-1V5-AA) or other
quality branded alkaline (lithium) batteries.
Do not throw the batteries in the trash. Deliver them to a civic
amenity site instead.
1.
2.
3.
4.
5.
Power
Typical lifetime
Low battery voltage
- Alkaline batteries
- Lithium batteries
Recommended installation height
PIR Detection angle / detection coverage:
Horizontal camera capture angle
Range of the flash
Resolution of the camera
Photo size LQ/HQ (typically)
Typical (LQ) photo transmission time to the control panel (ideally)
Typical (HQ) photo transmission time to the control panel (ideally)
Typical photo transfer time to the server
Dimensions, weight
Classification
- according to
- operational temperature range
- operational environment
- certification body
Also complies with
Can be operated according to
2 / 2
Formatting the Micro SD card
Changing the batteries
FW upgrade
Remove at least one battery from the detector.
Run the F-Link software. Connect the USB cable from your computer
to the mini USB connector (13) inside the detector.
Boot mode is indicated by flashing of the yellow LED.
Then continue the same way as if you were to upgrade the control
panel: Control panel → upgrade Firmware → choose the FW pack file →
in the window where you will be offered a device to upgrade select
the USB option and type of the device.
Disconnect the USB cable and re-insert the battery (batteries).
Technical specifications
2x alkaline battery type LR6 (AA) 1.5 V
(alternatively 2x AA lithium battery, 1.5 V)
about 2 years (1 activation and 1 series of photos a day)
Please note: Batteries are not included
Security grade 2/Environmental class II
EN 50131-1, EN 50131-2-2, EN 50131-5-3
JABLOTRON ALARMS a.s. hereby declares that the JA-160PC (90)
is in a compliance with the relevant Union harmonisation legislation:
Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU.
The original of the conformity assessment can be found at
www.jablotron.com - Section Downloads.
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer
after use.
≤2,52 V
≤2,62 V
2.5 m above the floor
90°/12 m
90°
max. 3 meters
LQ 320x240; HQ 640x480 pixels
2-20 kB/2-64 kB (6 kB/35 kB)
up to 20 sec. (10 sec.)
up to 130 sec. (60 sec.)
15 s/GPRS; 2 s/LAN
110 x 60 x 55 mm, 102 g
-10 to +40 °C
indoor general
Trezor Test s.r.o. (no. 3025)
ETSI EN 300 220, EN 50130-4,
EN 55032, EN 60950-1
ERC REC 70-03
MMQ53103
Advertisement
