Advertisement
4
Connecting the Switch
① Conne c t the 2- pin c onne c tor
from the switch by inser ting it
into the 2-pin connector coming
from the server.
② Position the switch in the desired
place and affix with double-sided
tape (round).
[ Reference 2 ] How to use the Cut Connector
1
2
10
mm
Peel off of the vinyl cover at
Peel off of the vinyl cover at the
connection.
end of the product's wire.
3
4
Wrap around both wire coils.
Close tightly with cut connector.
5
* W h e n c r i m p i n g , p l e a s e u s e
crimpers or use pliers to bend and
then solder together.
Insulate with vinyl tape.
Basic Operation
1
START
ENGINE
STOP
START
Key Switch ON
(Engine start)
Switching the Display
(Only X2-M5)
Troubleshooting
Trouble
Does not work with Engine start.
The opening demo works fine, but after that nothing happens.
The displayed values are different from the standard meter.
The boost pressure display is different from the standard or
other meter.
With the key in the ON position the boost needles points to a
minus reading.
Before the opening demo starts the needle briefly moves.
I can't change the display.
Only
X2-M5
Upon star ting up, the unit will star t in the newly
changed mode.
4
(Only X2-M5)
Switch
Double-sided Tape
(round)
Clean to remove
oil and dust
[ Reference 3 ] Notes about using the OBD Connector
10
mm
2
3
Opening Demo
Each pressing of the switch will
chang e the display b et we en
Boost and Water Temperature.
Poor connection of meter cable, OBD connector or fuse.
If wiring has been direct to power the red wire may have
been improperly wired or there is a poor connection.
The unit has been installed into an incompatible car model.
The unit has been installed into an incompatible car model.
Due to the ECU information received, the displayed values on this product may differ from those of stan-
dard or other meters.
This product's boost meter reads absolute pressure and may differ from a meter using relative pressure.
The sensor for absolute pressure is subtracting for barometric pressure and hence the display shows
minus. (EX: Elevation of 700 meters = minus 8 kPa)
This is due to a special characteristic of the meter and is not a malfunction.
Poor connection of 2-pin connector.
Because after changing modes, if the car's engine is turned off within 3 seconds, the new setting will not
be stored, make sure to wait at least 3 seconds before turning the engine off.
PIVOT CORPORATION
5
Fastening The Server
① Connect the meter cable and fuse power cord to the server.
• Meter Cable
3-pin
Connect to the server's 3-pin connector.
Connector
*The 3-pin connector can be connected to any of the three positions.
• Fuse Power Cable
Connect to the 1-pin connector coming
1-pin
from the black tube of the server.
Connector
② Use the provided double-sided tape (square) to fasten down the server in an out
of the way place.
③ Bundle up all loose wires and fasten together using the provided zip tie.
Make sure to grip the distended
portions when pulling it out or
inserting it.
If you unable to get a grip
on the distended portions.
With so me c ar m o d els it
m ay b e d i f f i c u l t t o g e t a
good grip on the connector.
4
Real display
Each meter will display
actual measurements.
Possible Causes
87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 JAPAN
CAUTION
D o n o t p u l l o n t h e w i r e s w h e n
trying to remove the connector; the
wires may become disconnected.
5
START
ENGINE
STOP
STOP
Meter OFF
Key Switch OFF
The needle stops at
(Engine stop)
the key OFF position.
1.5
0.5
While water tempera-
BOOST
x100 kPa
ture is on display the
TEMP
mode lamp will be ON.
x100 °C
0
-1
MULTI GAUGE
Possible Solutions
Please reconfirm whether wiring and
connections are correct or not.
Please check the "Fitting List".
Please check the "Fitting List".
Please reconfirm whether wiring and
connections are correct or not.
http://pivotjp.com/
In such case, pull
out the connector
by pulling on the
end of the zip tie.
Advertisement
