Advertisement
1
Connecting to a Power Source
①
Remove the Cover of the Fuse Box
Use a flathead screwdriver or such tool to remove
the cover of the fuse box found on the side of the
panel to the right of the steering wheel.
Fuse Box
Fuse Box
Fuse Box
If you are unable to get power from the fuse
box, please wire directly to IGN (12V with
key in ON position). *Do not connect the red
wire coming from the OBD connector.
2
Connecting the OBD Connector
①
Locate the Diagnostic Monitoring
Connector Position
Diagnostic Monitoring
Diagnostic Monitoring
Diagnostic Monitoring
About Using
OBD Products
in Combination
3
Fastening The Meter
Affix the supplied meter hood to the back
of the standard tachometer.
①
Remove the standard tachometer
Unscrew the two screws (torque screw T30 x 2) from the base at the back of the tachom-
eter and remove it by pulling it forward. (As the wiring for the tachometer is connected to
inside the steering column it cannot be removed. Carry out all operations with the wiring
pulled out but connected.)
*Make sure not to lose any removed parts.
Tachometer
(Backside)
Two screws
(torque screw
T30 x 2)
②
Unscrew the screws at the
back of the tachometer
Remove the screw from the hole at the
back of the tachometer.
*Put the bolt store in a safe place.
③
Affix Double-sided Tape to
the Stay on the Meter Hood
Af f i x t h e p r ov i d e d d o u b l e - s i d e d t a p e
(round) to the two places as shown in the
figure to the right.
The following is just one example of wiring to the fuse box of a BMW MINI COOPER S MF16S (steering
wheel on right). If your model is different and you are unsure of how to connect please contact your dealer.
②
Insert the Fuse
Remove the fuse for IGN (12 V with key
switch ON), and insert the 7.5 A mini-
fuse from the fuse power cable.
Cover
Meter
②
Open the Cover
Cover
Cover
Cover
Connector
Connector
Connector
Open
Open
Open
If you wish to use this product in combination with products in our 3-drive Series (FLAT or COMPACT), PROGAUGE , the "OBD2
Wiring Kit OBD-EH" (sold separately ¥3,200) makes installation a snap.
For more details about using combinations of products see here. http://pivotjp.com/obd-e/
this product
*When using the
with products mentioned above, they can only be used together in compatible model vehicles for both products.
The X2-M5 can be installed on either the left or right.Only carry out the following instructions on the side being used.
Installing without
removing tachometer
Cable
Cable
Cable
Tachometer
(Backside)
Remove
Hole
Double-sided Tape
(round)
[ Reference 1 ]
Ex: BMW MINI COOPER S MF16S (steering wheel on right, 2008 MODEL)
Fuse
Fuse
Fuse
(included)
(included)
(included)
(Front of the fuse box)
Server
1-pin Connector
③
Insert the OBD connec-
t o r t o t h e d i a g n o s t i c
m o n i tor i n g c o n n e c tor
from the server.
Diagnostic Monitoring
Diagnostic Monitoring
Diagnostic Monitoring
Connector
Connector
Connector
④
Lightly Fasten the Meter
Hood
L i n e u p t h e s c r e w h o l e s o n t h e
original tachometer with the screw
holes on the meter hood and lightly
fasten with the double-sided tape.
*Do not press to strongly on the tape;
it may become difficult to remove.
When installing the 52X-BW please
m ake ad ju s t m e nt s to li n e u p t h e
meters on each side.
⑤
Fix the meter hood with
the screws
U s e t h e p r o v i d e d t a p s c r e w s t o
fasten.
⑥
Return the tachometer
to its original position
Return the tachometer to its original
place by going in the reverse order
from ① above, and securely fasten
with the two screws.
⑦
Fasten the meter to the
meter hood
Affix the provided cushion tape to
two places on the sides of the meter.
Pull the meter cable through the hole
at the back of the meter hood and
insert it into the 5-pin connector at
the back of the meter. After having
decided the angle press the meter
into the hood at finish the installation.
Position = 4th column from the left
and 5th row from the top
Number = 32 or 34
Capacity = 7.5A
*If you wish to get power from a fuse
other than the 7.5A mini-fuse, please
purchase separately.
IGN
= Cut connector
(Not as normal power source)
(or soldering)
Cut
Fuse
Completely insert the OBD
Connector
Tachometer (Backside)
Meter Hood
(Backside)
Meter Hood (Backside)
Two screws
Meter Hood
Cushion tape (two places)
Meter Cable
Tap screw
(included)
3
Advertisement
