Table of Contents
Advertisement
Message Alert (for answering system)
This feature sets your answering system to give an alert tone every 10 seconds when there are new messages.
From the Handset Setup Menu:
1. Press the
cid/vol (▼ or ▲)
2. Press mute/menu button to enter the menu. NEW MSG ALERT 1ON 2OFF shows in the display.
3. Use the touch-tone pad to enter the selection, or use the
default setting is 2OFF.
4. Press the mute/menu button to confirm. You will hear a confirmation tone and the new setting shows in the display.
Rings to Answer (for answering system)
This feature lets you select the number of times you want the phone to ring before the answering system answers a call.
From the Handset Setup Menu:
1. Press the
cid/vol (▼ or ▲)
2. Press mute/menu button to enter the menu. RING TO ANSWER 3 4 5 6 TS shows in the display.
3. Use the
cid/vol (▼ or ▲)
4. Press the mute/menu button to confirm. You will hear a confirmation tone and the new setting shows in the display.
NOTE: If you select Toll Saver (TS) the unit answers after the 3rd ring if there are NEW messages, OR the
unit answers after the 5th ring if there are NO new messages. This allows user to access their answerer
from another location and then hang up after 4 rings to save long distance charges.
Message Length
This feature allow user to set the Memo recording time and ICM recording time.
From the Handset Setup Menu:
1. Press the
cid/vol (▼ or ▲)
2. Press the mute/menu button to enter the menu. MESSAGE LENGTH 1 MINUTE shows in the display.
3. Use the
cid/vol (▼ or ▲)
4. Press the mute/menu button to confirm.
Security Code (for answering system)
You can access the answering system from a tone dialing telephone in another (remote) location. The security code is
required for remote access, and it prevents unauthorized access to your answering system.
From the Handset Setup Menu:
1. Press the
cid/vol (▼ or ▲)
2. Press mute/menu button to enter the menu. SECURITY CODE 1 2 3 shows in the display.
3. Use the touch-tone pad to enter your new 3-digit security code. The default setting is 123.
4. Press the mute/menu button to confirm. You will hear a confirmation tone and the new security code shows in the
display.
NOTE: If you make a mistake, use the delete/int/conf button to backspace and erase the wrong digit.
Area Code
From the Handset Setup Menu:
1. Press the
cid/vol (▼ or ▲)
2. Press mute/menu button to enter the menu. SET AREA CODE - - - shows in the display.
3. Use the touch-tone pad to enter your 3-digit area code.
4. Press the mute/menu button to confirm. You will hear a confirmation tone and the new area code shows in the display.
NOTE: To restore the default setting to - - -, press and release delete/int/conf when SET AREA CODE
shows in the display.
Tone/Pulse
This feature allows user to change tone or pulse dialing.
1.
Press the
cid/vol (▼ or ▲)
2. Press the mute/menu button to enter the submenu, TONE/PULSE 1TONE 2PULSE shows in the display.
3.
Use the touch tone pad on the handset to select 1 or 2, or use the
"1TONE" is the default setting.
4. Press the mute/menu button to confirm.
Registration
Your packaged handset(s) are pre-registered and ready to use. It is not recommended that a handset be registered
again unless absolutely necessary.
From the Handset Setup Menu:
1. Press the
cid/vol (▼ or ▲)
2. Press the mute/menu button to enter the menu. REGISTRATION 1YES 2NO - - - shows in the display The default
setting is "2NO".
3. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the
4. If you select 1YES, press the mute/menu button to confirm your selection. HOLD BASE PAGE WAIT FOR BEEP shows
in the display. (Your handset should be held near the base during registration process.)
5. Press and hold the page button on the base unit you hear a tone at the handset. HANDSET X REGISTERED shows in
the handset display, where X stands for the handset number. You may now rename your handset. (Refer to Step 3 & 4
of Handset Name Section)
button to scroll to the MESSAGE ALERT sub-menu.
button to scroll to the RING TO ANSWER sub-menu.
button to scroll to your selection. The default setting is 5.
buttons
to scroll to the MESSAGE LENGTH submenu.
buttons
to scroll to your selection. "3 MINUTE" is the default setting.
button to scroll to the SECURITY CODE sub-menu.
button to scroll to the AREA CODE sub-menu.
buttons
to scroll to TONE/PULSE menu.
button to scroll to the REGISTRATION sub-menu.
cid/vol (▼ or ▲)
button to scroll to the 1ON or 2OFF. The
cid/vol (▼ or ▲)
buttons
button to scroll to 1YES or 2NO.
cid/vol (▼ or ▲)
to scroll to your selection.
Advertisement
Table of Contents
