Table of Contents
Advertisement
Press the
cid/vol (▼ or ▲)
button to select the desired record, then press the talk/flash or speaker button
2. When finished, press the end button to hang up.
NOTE: You may enter up to 32 pre-dial digits.
NOTE: If you want to delete the pre-dial number you entered, press the delete/int/conf button until all of the
digits are erased.
Answering Calls
1. When the phone rings, press the speaker button on the handset
- OR -
pick up the handset and press the talk/flash button.
2. When finished, press end button to hang up.
NOTE: Adjust the handset volume by pressing the
Call Timer
After you press the talk/flash or speaker button on the handset, the built-in call timer shows on the display and counts the
length of time of the call in minutes and seconds.
Auto Standby
If you place the handset in the cradle while the handset is off the hook (during a call), the call is automatically disconnected.
Ringer HI/LOW/OFF (Shortcut)
There are two ways to set the ringer to HI/LOW/OFF. One is the traditional way as described in the Programming Functions;
Handset Setup; Ringer Volume menus. The other one is this short cut to ringer menu.
1. Make sure the phone is OFF (not in talk mode).
2. Press the #PAUSE/RINGER button to display 1HI 2LOW 3OFF.
3. Use the touch tone pad on the handset to select 1, 2 or 3, or use the
is the default setting.
4. Press #PAUSE/RINGER button again to save and display the new selection for a few seconds.
Flash/Call Waiting
If you subscribe to the combined Call Waiting Caller ID service from your local telephone company, you will receive Caller
ID information (if available) on Call Waiting calls. During a phone call, you will hear a beep to indicate another call is waiting
on the line and Caller ID information for the waiting call shows on the handset display.
• To connect to the waiting call, press the talk/flash button on the handset, and your original call is put on hold.
• To switch between the two calls, press the talk/flash button.
Last Number Redial
You may redial a number up to 32 digits long. To quickly redial the last number you dialed:
1. Press the talk/flash button.
2. Press the redial/format button.
-OR-
3. Press the redial/format button first, then use the
- Press the
cid/vol (▼ )
to review the oldest call and scroll toward the most recent calls (higher numbers).
- Press the
cid/vol (▲)
to review the newest call and scroll to older calls (lower numbers).
NOTE: You may choose from three last dialed numbers.
4. Press the talk/flash button. The number dials automatically.
If you get a busy signal and want to keep dialing the number, press the redial/format button to quickly redial the number.
Exit
Press the end button to exit a menu function and return to the standby screen.
Page
The page feature helps you locate a misplaced handset. To send and receive pages, all handsets must be registered. If
your handset is not registered, follow the instructions in the Registration section of this manual.
Handset to Handset Paging (applicable only with additional handsets)
1. Make sure the phone is OFF (not in talk mode).
2. Press the delete/int/conf button on a handset.
3. Use the touch-tone pad to enter the handset number you want to page.
4. To cancel the page, press the end or delete/int/conf button on the originating handset, or press the end button on the
receiving handset.
Paging All Handsets from a Handset (applicable only with additional handsets)
1. Make sure the originating phone is OFF (not in talk mode).
2.
Press the delete/int/conf button on a handset. Paging Extension? Shows in display
3.Use the touch-tone pad to enter the handset number you want to page.(1=to page handset1, 2=to page handset 2 etc,
cid/vol (▼ or ▲)
button during a call.
cid/vol (▼ or ▲)
cid/vol (▼ or ▲)
button to select the desired redial number.
button to scroll to your selection. HI
Advertisement
Table of Contents
