Page 1
For more information go to www.P65Warnings.ca.gov. MADE IN CHINA Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-467-8643, 8 a.m. – 5:30 p.m., CST, Monday - Friday, or email info@sunheat.com - 1 -...
HARDWARE SAFETY INFORMATION SAFETY INFORMATION This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in the first few pages and is also located throughout this manual. Keep this manual for future reference and to educate new users of this appliance. This manual should be read in conjunction with the labeling on the appliance.
SAFETY INFORMATION ASSEMBLY PREPARATION Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package contents list and hardware as listed on pages 3 and 4 of this manual. If any part is missing or damaged, do not attempt to assemble this product.
Page 7
ASSEMBLY 1. Attach the Support Brackets to the Base. Attach the 3 - Support Brackets loosely to the Base with 3 - Medium Bolts inserted through the holes in the bottom of the Support Brackets and into the Base. Hardware Used: 3 Medium Bolts Attach the Post to the Support Brackets.
Page 8
ASSEMBLY Place Cylinder Housing onto Post. Slide Cylinder Housing down over Support Brackets and Post and rest on Base. 4. Attach Reflector Studs to Screen Cover. Insert 3 Reflector Studs through washers and into holes on screen cover. Tighten studs securely. Hardware Used: 3 Reflector Studs 3 Large Flat Washers...
Page 9
ASSEMBLY 6. Install Reflector. NOTE: MAKE SURE TO REMOVE PROTECTIVE PLASTIC COVER ON REFLECTOR PIECES PRIOR TO ASSEMBLY! Assembly Tip: If necessary for proper alignment of reflector sections, loosen each screw prior to further assembly and retighten after sections are aligned. Slide two Reflector Panels together.
Page 10
Connect the Hose and Regulator to the LP cylinder. The LP cylinder is sold separately Use a standard 20 propane cylinder only Lift the Cylinder Housing up and rest it on the top of the assembled Support Brackets. supports. Lower Secure the LPG tank by attaching the Chain onto the post the Tank housing.
OPERATING INSTRUCTIONS Leak Test 1. Make 2-3 oz. of leak test solution (one-part liquiddishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3. Apply several drops of solution where regulator connects to cylinder. 4.
Page 12
OPERATING INSTRUCTIONS Lighting: TO TURN ON THE HEATER 1. Turn the control knob to the “OFF” position. 2. Fully open the LP cylinder valve. 3. Press and turn the control knob to “HI” position (counterclockwise 90°). Press down the control knob and hold for 3-5 seconds. While holding down the control knob, press the igniter several times until the flame ignites.
Page 13
OPERATING INSTRUCTIONS NOTE: After use, some discoloration of the emitter screen is normal. Operation Checklist: For a safe and pleasurable heating experience, perform this check before each use: Before Operating: 1. I am familiar with entire owner’s manual and understand all precautions noted. 2.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Gas valve may be off Turn gas valve ON Fuel tank may be empty Refill LPG tank Orifice blocked Clean or replace orifice Purge air from lines. Open gas Air in supply system lines and depress control knob for 2-3 mins.
CUSTOMERS IN CANADA Only return this product to the store if it was purchased within 30 days. If you have problems after 30 days of purchase, please CALL 1-877-467-8643, or email info@sunheat.com. DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE.
Need help?
Do you have a question about the PHRDBK and is the answer not in the manual?
Questions and answers