4M 3-in-1 Mini Solar Robot Assembly Instructions

3-IN-1 MINI
SOLAR ROBOT
A. SAFETY MESSAGES
1. Adult supervision and assistance are required at all times.
2. This kit is intended for children aged 5 years and over.
3. This kit and its finished product contain small parts which may cause choking if misused. Keep away from children under 3 years old.
4. Do not attempt to take the solar panel apart.
5. Never look directly at the Sun as it could damage your eyes.
6. If using a desk lamp as a source of light, be aware that this will be hot. Only use a desk lamp under adult supervision.
B. CONTENTS
2
1
5 6
Part 1. Hook x 2, Part 2. Gearbox cover, Part 3. Faceplate, Part 4. Baseplate, Part 5. Wheel x 2, Part 6. Solar panel support, Part 7. Link arm
x 2, Part 8. Cam wheel x 2, Part 9. Foot x 2, Part 10. Leg x 2, Part 11. Connector x 8, Part 12. Solar gearbox, Part 13. Motor with wires, Part
14. Solar panel, Part 15. String, Part 16. Screws. Also required but not included: a small crosshead screwdriver.
C. ASSEMBLING THE SOLAR GEARBOX
1
1
2
1
1. Find the solar gearbox (part 12). Install the motor in the gearbox in the position shown, making sure that the gear on the motor shaft
interlocks with the gear wheel inside the gearbox.
2. Push one of the pins on the solar panel support (part 6) into the slot at the top of the gearbox. The rounded pins under the support must be
at the same end of the motor wires. Push the gearbox cover (part 2) into place, making sure the gear-wheel axles and the solar panel support
slide into the slots in the cover. Secure the cover with four screws to complete the gearbox assembly.
3. Push the contacts on the ends of the wires from the motor into the slots at the end of the solar panel support. Make sure the wires are on
the correct side as shown. Slide the solar panel into the solar panel support. The electrical contacts must be face down, and towards the motor
end of the gearbox. Secure the connection with two screws from the underside of the panel.
4. Push a cam wheel (part 8) onto the axle at each side of the gearbox, lining up the pin on each one with the marked guide. The axle and the
hole on the cam wheels are in a hexagonal shape. Wiggle the cam wheels a bit to fit them in. Your solar gearbox is complete. You
can use this shared mechanism in all three following sections.
D. ASSEMBLING THE SOLAR VEHICLE
1
1. Take the solar gearbox completed in Section C. Push a wheel (part 5) onto each cam, making sure the small pin on the wheel fits into the
small hole on the cam.
2. Push the faceplate (part 3) into the slots on the front of the gearbox (the opposite end as the motor). Push the baseplate (part 4) into the
slots on the underside of the gearbox, with the fin facing backwards.
3. Place the Solar Vehicle on a smooth, flat surface outdoors. Tilt the solar panel to point towards the Sun. The Vehicle should start to move
along using energy from the Sun.
PLEASE SCAN THE QR CODE FOR VIEWING MULTI-LANGUAGE INSTRUCTIONS.
3
4 1
5
2
2
FR. Veuillez scanner le code QR pour afficher les
instructions multilingues pour ce kit. DE. Bitte scanne den
QR-Code, um die mehrsprachige Anleitung für dieses Set
anzusehen. NL. Scan de QR-code om de instructies voor
deze set in verschillende talen te bekijken. IT. Scansiona il
codice QR per visualizzare le istruzioni multi-lingua per
questo kit. ES. Escanee el código QR para ver instrucciones
QRコードをスキャンして、 本
en varios idiomas para este kit. JA.
キットの多言語説明書をご覧ください。
7 9
8 10
8 9
10
7
3
RED
WARNING:
CHOKING HAZARD -
Not for Children under 3 years.
TO PARENTS: PLEASE READ THROUGH THESE INSTRUCTIONS
BEFORE GIVING GUIDANCE TO YOUR CHILDREN.
12
13
11
14
11
15
16
4
BLUE
3
Small parts
X 6