Download Print this page

Waltons 05ARBT0502-V1 Quick Start Manual

Advertisement

Quick Links

05ARBT0502-V1 & 05ARBO0502-V1
Overall Dimensions:
Length = 736m
Width = 1669cm
Height = 1876cm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be a ected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance
work and annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also
recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71
level, we cannot accept responsibility for your safety whilst erecting or using this product.
15/11/2011
x2
This building should be erected by
two people.
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
2mm Drill bit
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
For Assistance Please
Contact Customer Care on
01636 880514
Please retain product label and instructions for future reference
05ARBT0502-V1 Content
1
Roof Qty 2
4
Seat Back Qty 1
05ARBO0502-V1 Content
1
Roof Qty 2
4
Seat Back Qty 1
3
2
Side Qty 2
Seat Qty 1
3
2
Seat Qty 1
Side Qty 2

Advertisement

loading

Summary of Contents for Waltons 05ARBT0502-V1

  • Page 1 05ARBT0502-V1 & 05ARBO0502-V1 15/11/2011 Please retain product label and instructions for future reference 05ARBT0502-V1 Content Overall Dimensions: Length = 736m Width = 1669cm Height = 1876cm Before assembly please make sure you have a suitable base ready to erect your...
  • Page 2 Fixing Kit We strongly recommend pre drilling Step 1 for both 02ARBT0502-V1 & 05ARBO0502-V1 holes before xing screws. Place the side onto the two posts making sure that the two edges are flush with the post. Post - 75x75x1500mm Qty 4 Place the side 65mm from the end of the posts, secure using 6x60mm screws.
  • Page 3 Step 3 We strongly recommend pre drilling Step 5 We strongly recommend pre drilling holes before xing screws. holes before xing screws. Before attaching the seat to Attach the seat joining batton the posts ensure that the seat in the gap between the seat is level at all four posts and and the seat back, using 40mm 400mm from the floor.
  • Page 4 12 x 50mm Screws bars. Step 10 05ARBT0502-V1 HAS BEEN USED FOR ILLUSTRATION Attach the assembled parts to Attach the side supports to the PURPOSES ONLY THE STEPS REMAIN THE SAME. posts flush to the roofs on...
  • Page 5 Step 11 We strongly recommend pre drilling holes before xing screws. Attach the fascias to the front and back of the arbour seat flush with the roof support bars using 40mm screws. 12 x 40mm Screws Step 12 Attach the roof capping strip We strongly recommend pre drilling ontop of the roofs and fix holes before xing screws.

This manual is also suitable for:

05arbo0502-v1