Download Print this page

Waltons 03COR0707-V4 General Instructions Manual

7x7 corner summerhouse

Advertisement

Quick Links

General Instructions
03COR0707-V4
7X7 CORNER SUMMERHOUSE
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, wood saw, step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be a ected during various weather conditions. For the duration of heavy or
extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproo ng treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions,
The base should be slightly smaller than the external measurement of the building, i.e. The cladding should overlap
the base, creating a run o for water. It is also recommended that the oor be at least 25mm above the surrounding
ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
Refer to the instructions pages for you speci c product code
Please retain product label and instructions for future reference
x2
All building's should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every e ort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
P 1

Advertisement

loading

Summary of Contents for Waltons 03COR0707-V4

  • Page 1 Please retain product label and instructions for future reference All building’s should be Winter = High Moisture = Expansion erected by two adults Summer = Low Moisture = Contraction 03COR0707-V4 7X7 CORNER SUMMERHOUSE BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY For ease of assembly, you CAUTION...
  • Page 2 03COR0707-V4 Please retain product label and instructions for future reference Overall Dimensions: Roof Frame - 28 x 28 x 2049mm QTY 1 Fascia - 12 x 95 x 2045mm QTY 2 Length = 2073mm FS2828-2049MM S1295-2045MM Width = 2073mm Height = 2145mm...
  • Page 3 Please retain product label and instructions for future reference Pre Assembly Pre Assembly Remove transportation blocks Position press lock on the door align with key hole and x into from the bottom of each panel before beginning assembly. position using 4 x 10mm screws. Each Panel should have two.
  • Page 4 Please retain product label and instructions for future reference Step 3 Step 1 Place rear panel left against Place the oor on a the oor and the window rm and level base, side. ensure the base has suitable drainage, Fix into place using free from areas 3x50mm screws as shown in where standing water...
  • Page 5 Please retain product label and instructions for future reference Step 6 Step 5 Layout the roof sheet and Position the support bar across the position the roof framing building from the left window panel onto the sheet as shown in upright framing to the opposite the diagram.
  • Page 6 Please retain product label and instructions for future reference Please retain product label and instructions for future reference Step 8 Step 10 Cut three strips from the roll of felt, Fit the fascias to the 2x3020mm and 1x1420mm in length. Felt building over the felt and Corner...
  • Page 7 Please retain product label and instructions for future reference Step 12 Step 14 Attach the rain guards to the Attach the larger rain guard building, xing in place above above the door, xing in place each window using 3x60mm using 3x60mm screws. screws per guard.