Table of Contents
Advertisement
Installation Manual
Applicable to the following remote start system:
CM800-S – Auto Only Starter Control Module
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions;
(1) This device may not cause harmful interference.
(2) This device may accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this device.
By Firstech LLC, Version: 1.1
WWW.COMPUSTAR.COM
Advertisement
Table of Contents
Related Manuals for CompuSTAR Firstech CM800-S
Summary of Contents for CompuSTAR Firstech CM800-S
- Page 1 (1) This device may not cause harmful interference. (2) This device may accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. WWW.COMPUSTAR.COM...
-
Page 2: Table Of Contents
Table of Contents Introduction ............................3 Kit(s) Contents ............................3 Installation Basics ..........................4 Key Points to Consider Before Installation: ..................4 Remote Code Routine(s) ........................5 Placement and Use of Components ..................... 5 Common Procedures ..........................6 Valet Mode ............................6 Jumper Settings ........................... -
Page 3: Introduction
We highly recommend that you contact your local Firstech dealer and seek professional installation. Call 888-820-3690 or visit our website at www.compustar.com to locate your nearest dealer. Caution: The Manufacturer’s warranty will be void if this product is installed by anyone other than an authorized dealer. -
Page 4: Installation Basics
Installation Basics If you are new to installing Firstech remote start units, we highly recommended that you review this manual in its entirety prior to installing your first unit. Key Points to Consider Before Installation: The two remotes are preprogrammed to the unit Page 5 This system is designed for ease of installation and the two included remotes are preprogrammed. -
Page 5: Remote Code Routine(S)
Remote Code Routine(s) IMPORTANT: The remotes are preprogrammed to the control module. In the event that you need to program the remotes follow the instructions below. Programming the Remote STEP 1: Activate Programming mode by turning the ignition key on and off (between the Acc & On positions) five times within 10 seconds. -
Page 6: Common Procedures
Common Procedures Valet Mode When servicing or loaning your vehicle to others, your remote start system should be placed in Valet Mode. Valet Mode prevents the system from remote starting and disables all alarm functions. IMPORTANT: While in Valet mode the remote start will still lock and unlock power lock systems. The system can be put into valet one of two ways: 1. -
Page 7: Alternator Sensing - Option 2-04 Setting 3
STEP 2: Test wire and make connection. With the vehicle off the wire should test 0 Volts AC. At idle the tach wire should test between 1 to 5 Volts AC. As the vehicle RPM’s increase the voltage on the meter will also increase. -
Page 8: Diesel Timer
The CM800-S control module is firmware updatable through the internet. In the event Firstech makes any changes or corrections you can update the module using the RS232 port on the control module. This feature is a detailed process so please follow instructions on www.compustar.com. -
Page 9: Cm800-S Wiring Schematic (Remote Start)
CM800-S Wiring Schematic (Remote Start) - Page 10 Connector 1 (CN1), 8-Pin Ignition Harness Pin 1 Red - Constant 12V positive (+) power input. This wire must be connected. The proper vehicle wire will test (+) 12V at all times - while the key is in the off position, the on position and during crank.
- Page 11 Pin 3 White/Black - 2nd Accessory 250mA negative (-) output. This output can be used to trigger the pre-wired relay located on the main ignition harness. Pin 4 Black – Status/Ground while running 250mA negative (-) output. This is an optional output that will provide a negative (-) output before the ignition cranks and stay on throughout the remote start duration.
- Page 12 Pin 3 Orange/Black – 2 Pulse Unlock wire. This wire is used to provide the customer with a driver’s priority unlock feature with option 1-04. With the option on the unlock (blue) wire will pulse first and then orange/black will pulse if the unlock button is pressed again within 3 seconds. Pin 4 Blue - Unlock 250mA negative (-) output.
-
Page 13: Option Programming Tables
Option Programming Tables Optional Optional Optional Feature Default Setting - I Setting - II Setting - III Setting - IV Unlock Before, Lock After Lock After Start Lock After 1-01 Starting Only Shutdown Only Lock / Unlock Pulse 1-02 0.8 sec 2.5 sec 0.125 sec 3.5 sec... -
Page 14: Option Menu Descriptions
3-02 Aux 1 Output 0.5 Second Latched 20 Seconds Program 3-03 Aux 2 Output 0.5 Second Latched 60 Seconds Program 3-04 Aux 1 Output Control By Remote Disarm Ignition Off 3-05 Aux 2 Output Control By Remote Disarm Panic Horn Mute Control on 3-06 Disabled Enabled... - Page 15 Driver’s Priority Unlock - The driver’s door must be isolated from the other doors. Use the 1-04 Orange/Black CN3 as your 2 Unlock output. Double Pulse Disarm Wire – This feature turn the disarm wire into a double pulse output for 1-05 shutting down factory alarm outputs.
- Page 16 2-05 Minimum Crank Time - This feature applies to feature 2-02. It will add or remove crank time to the default setting of the afore mentioned option. Diesel Timer – Use this option if you can’t find the glow plug wire. You can use setting 2 for a 2-06 default wait-to-crank;...
-
Page 17: Option Programming
Option Programming How to Program Options There are two ways to set options on the CM8 control modules. You can use the FT-OP500-KIT or most Firstech remotes. The remotes include 4 or 5 button 1 and 2 Way remotes. Option Programming Using the FT-OP500-KIT The OP500 can be used to change anything in the Option Tables. - Page 18 Lock + Unlock for 3 Hold Trunk Tap Key Tap Lock Tap Unlock Option seconds then Lock + Button for 3 Menu 1 Button Button Button Unlock for 3 seconds seconds Lock + Unlock for 3 Hold Trunk Tap Key Tap Lock Tap Unlock Option...
-
Page 19: Troubleshooting
Troubleshooting Remote Start Error Codes If the remote start fails to start the vehicle, the parking lights will flash three times immediately. Following those three flashes the parking lights will flash again corresponding to the error table; Number of Parking Light Remote Start Error Flashes Motor running | or | must program tach... - Page 20 A: The auxiliary outputs on this unit can be triggered via two analog wires or through a supported bypass module. All my connections are made, how do I program the tach? A: Start the vehicle with the key. Hold the foot brake down. While holding the foot brake down hold the Start button down for 3 seconds.
-
Page 21: Technical Support Contacts
Technical Support Contacts Firstech technical support is reserved for authorized dealers only. Monday - Friday 888-820-3690 (8:00 am – 5:00 pm Pacific Standard Time) Email support@compustar.com techfeed.compustar.com Wiring Diagrams Go to www.firstechonline.com to access Computech3. If you are an authorized dealer and unable to access this site please contact your sales rep or us call 888-820-3690 Monday through Friday, 8 am to 5 pm Pacific Standard Time.