Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for The Pool Factory APF325PRO
Summary of Contents for The Pool Factory APF325PRO
- Page 1 CARTRIDGE FILTER FOR POOLS & SPAS Mega Cartridge Filter OWNER'S MANUAL 877.278.2797 fax 877.289.2963 ATTENTION INSTALLER: THIS MANUAL CONTAINS IMPORTANT INFORMATION ON THE OPERATION, AND SAFE USE OF THIS EQUIPMENT. THIS MANUAL IS INTENDED FOR THE END USER OF THIS PRODUCT...
-
Page 2: Table Of Contents
Operating Instructions and Parts List Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. -
Page 3: General Safety Information
General Safety Risk of falling This filter is not and drowning. designed for Information (Continued) backwashing. If unit is plumbed backwards or backwashed, it will Risk of meters) from pool (or spa) so that damage the filter cartridge and will electrical children cannot climb over it into void the warranty. -
Page 4: Specifications
Pressure: ... 50 psi (345 kPa) Maximum Continuous Water Temperature: ..104° F (40° C) OUTLET INLET REQUIRED CLEARANCE "B" SIDE "C"ABOVE APF325PRO APF425PRO APF525PRO 44.3 112.5 TOP MANIFOLD CARTRIDGE FILTERS DESIGN FLOWRATE EFFECTIVE FILTRATION RATE... -
Page 5: Installation Procedures
7. Connect the bottom filter port 4. If practical, place pump and filter in Operating Instructions and Parts List (filter OUTLET) to the pool the shade to shield it from Installation Procedures return plumbing lines. continuous, direct heat from the sun. This filter should only be installed by qualified personnel. -
Page 6: Initial Start-Up
Starting the Pump and Filter Place the manual air relief valve System in OPEN position. (See Fig 2) FILTERING Filtration starts as soon as flow is Starting Pump WARNING steady through the filter. As the filter When starting system pump, removes do not stand over or near filter. -
Page 7: Filter Disassembly
6. Holding both ends of the filter clamp FILTER DISASSEMBLY INSTRUCTIONS MAINTAINING YOUR FILTER carefully spread the clamp ends. 1. Turn off all system circulation pumps Remove the clamp by lifting over the and all electric power on the equipemt WARNING pad. -
Page 8: Cartridge Cleaning
When using PHMB Wear The pressure gauge (polyhexamethylene rubber is the primary biguanide) based sanitizers, such as gloves, protective clothing indicator of filter performance. Maintain Baquacil , special care must be taken and safety goggles when the pressure gauge in good working ®... -
Page 9: Filter Assembly
BODY AND CLAMP RE- Filter Re-Assembly Never rely on hand tightening of ASSEMBLY clamp nut to clamp bolt. Using a 3/4” Instructions socket on a torque wrench, torque 1. Place the metal reinforced seal clamp nut to clamp bolt to 150 inch- on lower filter body. - Page 10 REMOVING THE MANUAL This product should be installed AIR RELIEF VALVE and serviced only by a qualified pool WARNING professional. RE-INSTALLATION OF THE MANUAL AIR RELIEF VALVE 1. Check the o-ring seals, replace as needed. This product should be With a clean cloth, wipe upper filter installed and serviced only by a body and o-ring groove.
-
Page 11: System Inspection
Series 59725, 59726 and 59727 System Inspection Do not over tighten Troubleshooting Guide valve. If the valve The pool circulation system should be fails to seal, turn the pump off, remove Short Cycle Time the top assembly and inspect the valve frequently inspected for debris and Cycle time will vary between o-ring. - Page 12 Operating Instructions and Parts List Chemical imbalance in water: Check Drain and skimmer valves are not Water Not Clear pool chemistry (refer to Table 1 fully open: Fully open the drain and A number of factors can affect water on page 3). Consult local pool skimmer valves clarity.
-
Page 13: Replacement Parts
Item Part No. Description Pressure Gauge 60033-01 60033-02 Manual Air Relief Assembly Upper Filter Body 60034-03 for 325 / 425 Upper Filter Body 60033-03 for 525 Clamp System including: Clamp, Clamp Nut and Bolt, 60033-04 Hang tag, Metal Reinforced Seal, and Labels 60033-05 O-RING 60033-06... - Page 14 Operating Instructions and Parts List Limited Warranty For one (1) year from the date of purchase, will repair or replace, at its option, for the original owner any parts of its filters (“Product”) which are found upon examination to be defective in materials or workmanship. This Limited Warranty covers labor for a period of one (1) year.
Need help?
Do you have a question about the APF325PRO and is the answer not in the manual?
Questions and answers