Table of Contents
Advertisement
INFORMATION TO THE USER
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by
user. This equipment complies with FCC/ IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator at least 20 cm or more away from
person's body (excluding extremities: hands, wrists, feet and ankles). Alteration
or modifications carried out without appropriate authorization may invalidate the
user's right to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
□ Relocate or reorient the receiving antenna.
□ Increase the separation between the equipment and receiver.
□ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
CAUTION!!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
11
TROUBLE SHOOTING GUIDE
TROUBLE
CAUSE
The fuse is blown
Unit will not turn on
Ignition not engaged
Blown speaker
Volume is low / muted
No sound is heard
Device is paused or muted
The Bluetooth function of the
device is not enabled
Cannot pair Bluetooth
The MC900B memory is full
The audio quality is poor
after connection with a
Bluetooth enabled device
The Bluetooth reception is poor
Unit has become
unresponsive
Power glitch or interference
SPECIFICATIONS
BLUETOOTH
• BT: 4.0
• BT Range: 33Ft / 10M (Class 2)
• BT Profiles: A2DP
AMPLIFIER
• Channels: 4
• MAX Continuous Output: 500W
(All channels driven)
• PEAK Power Rating:
- 4Ω: 125W /channel
• RMS Total Power Output: 150W
• Class: AB
• Frequency response: 20-25kHz
• 4Ω stable
• Input impedance: 22k Ohm
CHASSIS
• Chassis Dimensions HxDxW :
1.75"x 7.8" x 3.8" / 44.5mm x 198mm x 96.5mm
• Controller Dimensions HxDxW:
0.81"x 3.75" x 1.85" / 20.5mm x 95.2mm x 47mm
• Controller cable length: 20ft / 6m
• Backlight illumination control wire
• Quick connect Molex power harness
SOLUTION
Check / replace the fuse
Turn ignition to on position
Replace faulty speaker
Press the volume level up
Check your devices playing /
volume status
Refer to the user manual of the
device for how to enable the
Bluetooth function
Follow how to clear the memory
on PG 8
Move the device closer to the
audio system or remove any
obstacle between the device
and the systems antenna
Disconnect power for
10 seconds to reset
GENERAL
• Power source: 14.4VDC (10.8V ~ 16V allowable)
• Grounding System: Negative type
• Maximum Current Consumption: 15A
• 3-way protection circuitry (thermal, overload, and
speaker short protection)
• USB output voltage: 5VDC @ 1A
• Unit Weight: 2.08lbs / 0.94kg
• Storage Temperature: 5
F / -15
C to 45
o
o
o
F to 113
• Operation Temperature: 14
F / -10
o
F to 104
o
o
C to 40
• Replacement Fuse: 15A
(Replace with ATO Fuse Type Only)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
o
C
o
C
12
Advertisement
Table of Contents
