1. Manuals
  2. Brands
  3. ICP DAS USA Manuals
  4. Security System
  5. ALM-Horn Series
  6. User manual

ICP DAS USA ALM-Horn Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ALM-Horn Series User's Manual
www.icpdas.com
Warranty
All products manufactured by ICP DAS are under warranty regarding
defective materials for a period of one year from the date of delivery to the
original purchaser.
Warning
ICP DAS assumes no liability for damages resulting from the use of this
product. ICP DAS reserves the right to change this manual at any time without
notice. The information furnished by ICP DAS is believed to be accurate and
reliable. However, no responsibility is assumed by ICP DAS for its use, or for any
infringements of patents or other rights of third parties resulting from its use.
Copyright
Copyright 2020 by ICP DAS. All rights are reserved.
Trademark
The names used for identification only may be registered trademarks of their
respective companies.
ALM-Horn Series
User's Manual (Rev1.0, NOV/2020) ------------- 1

Advertisement

Table of Contents
loading

Summary of Contents for ICP DAS USA ALM-Horn Series

  • Page 1 ALM-Horn Series User’s Manual www.icpdas.com Warranty All products manufactured by ICP DAS are under warranty regarding defective materials for a period of one year from the date of delivery to the original purchaser. Warning ICP DAS assumes no liability for damages resulting from the use of this product.
  • Page 2 ALM-Horn Series User’s Manual Document Revision Version Date Description of changes Rev1.0 2020-11-04 First release for ALM-Horn Series ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 2...

  • Page 3: Table Of Contents

    Connector Pin Define ............... 9  2.2  Configuration & Setting ..............10  2.2.1  Reset to default for ALM-Horn-WF(-BR) only ......... 10  2.2.2  Dip Switch Select (All ALM-Horn series) ......... 11  2.3  Dimensions ..................12  2.4  Wire Connection ................13  2.4.1  Wire connection define ..............13 ...

  • Page 4: Introduction

    ALM-Horn Series User’s Manual 1. Introduction The ALM-Horn Series include 3 model, -BR with water clean upper cover, ALM- Horn as standard siren, Blue + Red LED, ALM-Horn-WF have WLAN connection complies with the IEEE802.11b/g/n standards, support Modbus TCP protocol & HTML, ALM-Horn-MRTU have RS-485 interface support Modbus RTU protocol.

  • Page 5: Features

     NC/NO Input Selectable 1.1.1 Features Description The ALM-Horn series device accepts any dry contact to trigger DI input, when the alarm been trigger it output from Piezo Transducer, LED’s & open collector DO. ALM-Horn series include 4 kinds of alarm tone, the DIP switch’s select which tone when DI been trigger, DIP switch also select the DI trigger mode NC (Normal Close) or NO (Normal Open).

  • Page 6: Specifications

    ALM-Horn Series User’s Manual Specifications Table 1-1: System Specifications Device ALM-Horn(-BR) ALM-Horn-WF(-BR) ALM-Horn-MRTU(-BR) Alarm Output 120 ± 5 dB @10cm/3.0 KHz (W/O waterproof membrane) Piezo Transducer Pressure Level Water clear upper cover with Ultra-Bright RED LED x 8 -BR: With 8 Blue + 8 Red Ultra-Bright LED...
  • Page 7 ALM-Horn Series User’s Manual Device ALM-Horn(-BR) ALM-Horn-WF(-BR) ALM-Horn-MRTU(-BR) LED Indicators Power/Status 2 colors LED, Blue for System status, Red for Alarm status. Protection IP43 (Panel Mount Upright Position) Waterproof ±8 kV Air for Random Point ESD (IEC 61000-4-2) ±2 kV for Power...

  • Page 8: Hardware

    ALM-Horn Series User’s Manual 2. Hardware 2.1 Outward Appearance Piezo Transducer output Waterproof membrane inside Figure 2-1: Front Panel Connector Figure 2-2: Back Panel ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 8...

  • Page 9: Connector Pin Define

    ALM-Horn Series User’s Manual 2.1.2 Connector Pin Define Figure 2-3: I/O Connector of ALM-Horn-MRTU(-BR) Figure 2-4: I/O Connector of ALM-Horn(-BR) & ALM-Horn-WF(-BR) ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 9...

  • Page 10: Configuration & Setting

    ALM-Horn Series User’s Manual 2.2 Configuration & Setting Reset to default Dip Switch Figure 2-5: Switches on the PCB 2.2.1 Reset to default for ALM-Horn-WF(-BR) only Remove the back panel, Press & hold the Reset button on the side bottom over 6 Sec until the Red LED(Status/Alarm) quick flash then release to restore device default setting.

  • Page 11: Dip Switch Select (All Alm-Horn Series)

    ALM-Horn Series User’s Manual 2.2.2 Dip Switch Select (All ALM-Horn series) Dip Switch Switch Index Waveform Figure 2-6: Alarm Tone select switch for DI trigger alarm Dip Switch Switch Input Mode NO(Normal Open): Short to GND Alarm NC(Normal Close): Open from GND Alarm Figure 2-7: DI Input Mode (NO/NC) select switch Note: Change the Input Mode NC/NO must restart the power to take effect.

  • Page 12: Dimensions

    ALM-Horn Series User’s Manual 2.3 Dimensions The diagrams below provide the dimensions of the ALM-Horn series to use in defining your enclosure specifications. All dimensions are in millimeters. Figure 2-8: Dimension of the ALM-Horn series ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 12...

  • Page 13: Wire Connection

    ALM-Horn Series User’s Manual Wire Connection 2.4.1 Wire connection define The following describe the wire color Figure 2-9: Wire color 2.4.2 I/O connection 2.4.2.1 Digital Input (DI) wiring Figure 2-10: DI Dry contact wiring ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 13...
  • Page 14 ALM-Horn Series User’s Manual 2.4.2.2 Open Collector Digital Output(DO) wiring Figure 2-11: Open Collector Output wiring 2.4.2.3 RS-485 wiring for ALM-Horn-MRTU Figure 2-12: RS-485 wiring for ALM-Horn-MRTU ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 14...

  • Page 15: Software

    ALM-Horn Series User’s Manual 3. Software 3.1 ALM Utility for ALM-Horn-WF(AP Mode) The Utility provides the simple way to operating and acquire I/O status. The Utility can use the wireless network interface to configuration. Provide AP(Access Point) & STA(Station) mode to connect the ALM-Horn-WF.

  • Page 16: Controller Status

    ALM-Horn Series User’s Manual 3.1.2 Controller Status Show the connected controller information, user define Locate string, RSSI strength, Device IP & Static IP button for changing device IP in STA mode. 3.1.3 DI/DO Status & Control Show the DI/DO status, The value can be read DI or set DO with Tone Index in this area.

  • Page 17: Icon Button

    ALM-Horn Series User’s Manual 3.1.4 Icon Button ICON function Open the Setup Screen (Android versions Setup Setup function under the icon) Red Led blinking, use to find the connected Find Controller Controller Refresh status Refresh Only Android Device, Menu Include setup, FW Version & About.

  • Page 18: Configuration/Setup

    ALM-Horn Series User’s Manual 3.1.5 Configuration/Setup Figure 3-2: ALM Utility setup page Click apply icon to save each subject’s setting, after finish all setting click to make device take effect on new setting AP： SSID Name 1. Default Controller’s SSID in Wi-Fi AP mode, will be ALM-06-xxxxxx.
  • Page 19 ALM-Horn Series User’s Manual Static IP: IP: Specific an IP that is not been used. Mask: Default will be 255.255.255.0. Gateway: Basically define in the AP you are going to connect. Service Set Identifier: Connected devices must be the same SSID, SSID SSID length must not exceed 31 characters.

  • Page 20: Ip Scanner

    ALM-Horn Series User’s Manual 3.1.6 IP Scanner There are lots of free IP scanner tools in both Windows & Android OS, for example “Advanced IP Scanner” for Windows, “Network Analyzer” for Android, those are high performance scanner tools on each OS.

  • Page 21: Modbus Protocol

    ALM-Horn Series User’s Manual 4. Modbus Protocol 4.1.2 Function Code The function code field of a Modbus data unit is coded in one byte. Valid codes are in the range of 1 ... 255 decimal (the range 128 - 255 is reserved and used or exception responses).

  • Page 22: Data Encoding

    ALM-Horn Series User’s Manual 4.2 Data Encoding Modbus uses a “big-endian” representation for address and data items. This means that when a numerical quantity larger than single byte is transmitted, the most significant byte (MSB, also called the high-order byte) is send first. The following sub- topics describe the different byte of encoding and show how the data is encoded as it is within the Modbus packet.

  • Page 23: Modbus Tcp Protocol Description

    ALM-Horn Series User’s Manual 4.3 Modbus TCP Protocol Description The Modbus protocol defines a simple protocol data unit independent of the underlying communication layers. The mapping of Modbus protocol on network can introduce some additional fields on the application data unit.

  • Page 24: Alm-Horn-Wf/-Mrtu Address Mapping

    ALM-Horn Series User’s Manual 4.4 ALM-Horn-WF/-MRTU Address Mapping Address Descriptions Range Access Type 00001 Alarm with Tone index 0 0=OFF, 1=ON 00002 Alarm with Tone index 1 0=OFF, 1=ON 00003 Alarm with Tone index 2 0=OFF, 1=ON 00004 Alarm with Tone index 3...
  • Page 25 ALM-Horn Series User’s Manual Technical Support If you have problems about using the ALM-Horn Series device, please contact ICP DAS Product Support. Email: service@icpdas.com ALM-Horn Series User’s Manual (Rev1.0, NOV/2020) ------------- 25...

This manual is also suitable for:

Alm-hornAlm-horn-brAlm-horn-wfAlm-horn-wf-brAlm-horn-mrtuAlm-horn-mrtu-br

Table of Contents