Page 1
ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. ee the label attached on the product and give the information to your dealer when you ask for service. User’s Guide W1946T W2046T...
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
Page 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching.
Page 5
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards DVI-D Signal Cable (This feature is not available in all countries.) (Only W1946T/W2046T/ W2246T/W2346T...
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Body into the product in the correct direction as shown in the picture.
Connecting the Display Disassembling the stand Put a cushion or soft cloth on aflat surface. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it.
Page 8
Connecting the Display Pull out the Stand to remove. Pushing the PUSH button, Take the stand body from hinge body. Good Position Bad Position Warning: You can hurt your finger.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~15˚...
Connecting the Display Connecting with the PC Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connect signal input cable of the signal cable. Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view.
Page 11
Connecting the Display Connecting with the PC Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connect signal input cable of the signal cable. Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view.
Control Panel Functions Front Panel Controls W1946T/W2046T/W2246T/W2346T W1946S/W2046S/W2246S/W2346S MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds.
Page 14
Control Panel Functions MODE Button AUTO Button INPUT Button (SOURCE Hot key) EXIT Button Power Button & Power Indicator Use this button to enter F-ENGINE, ORIGINAL RATIO menus. For more information, refer to page 20. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button before entering the On Screen Display(OSD).
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu BRIGHTNESS PICTURE CONTRAST SHARPNESS COLOR COLOR TEMP (PRESET / USER) GAMMA DISPLAY HORIZONTAL VERTICAL CLOCK PHASE LANGUAGE OTHERS POWER INDICATOR WHITE BALANCE FACTORY RESET...
Page 17
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
Page 18
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu Sub menu Description To adjust the brightness of the screen.
Page 19
On Screen Display(OSD) Selection and Adjustment Main menu W1946T/W2046T/W2246T/W2346T W1946S/W2046S/W2246S/W2346S Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu Sub menu Description HORIZONTAL To move image left and right. To move image up and down. VERTICAL To minimize any vertical bars or CLOCK...
Page 20
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu NOTE If this does not improve the screen image, restore the factory default settings. If necessary, execute the WHITE BALANCE function again.
Page 21
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MODE Button, then the main menu of the OSD appears.
Page 22
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Move : Select another sub-menu Sub menu Description NORMAL Select this when you want to use the product in the most general using environment. MOVIE Select this when you are watching a video or movie.
Page 23
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Move : Select another sub-menu Sub menu Description WIDE Switch to full screen mode according to input image signal. Change the input image signal ratio to ORIGINAL original. * This function works only if input resolution is lower than monitor ratio (16:9).
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the display connected? Is the power indicator light on? Is the power indicator flickering? Do you see an "OUT OF RANGE" message on the screen? Do you see a "CHECK SIGNAL CABLE"...
Troubleshooting Display image is incorrect Display Position is incorrect. On the screen background, vertical bars or stripes are visible. Any horizontal noise appearing in any image or characters are not clearly portrayed. IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed.
Page 26
Troubleshooting Display image is incorrect The screen color is mono or abnormal. The screen blinks. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? Have you installed the display driver? • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary.
Specifications Preset Modes (Resolution) W1946T/W1946S Display Modes (Resolution) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1360 x 768 W2046T/W2046S Display Modes (Resolution) 720 x 400 640 x 480 640 x 480 800 x 600...
Page 36
Specifications W2246T/W2346T/W2246S/W2346S Display Modes (Resolution) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 Indicator MODE On Mode...
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. Place the monitor with its front facing downward on a soft cloth. Separate the stand by pushing the PUSH button. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate.