Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching.
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards DVI-D Signal Cable (This feature is not available in all countries.) NOTE This accessories may look different from those shown here.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Connecting the stand base or Removing the stand base Place the monitor with its front facing downward on a cushion or soft cloth. Assemble the Stand Base into the Stand Body.
Connecting the Display Use a coin on the back of the stand base and turn the screw clockwise to tighten. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise.
Connecting the Display Height Range : maximum 4.33 inches (110.0 mm) When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). When adjusting the height of the screen, do not put your finger(s) in between the head of the monitor and the stand base.
Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. Lift the monitor to its highest height to utilize the Pivot function. . Landscape & Portrait : You can rotate the panel 90 Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function.
Connecting the Display Connecting with the PC Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connect signal input cable of the signal cable. Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view.
Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds.
(display mode). The best display mode is E1910P:1280 x 1024 E2210P:1680 x 1050 When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal is connected, it is automatically detected.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu BRIGHTNESS PICTURE CONTRAST SHARPNESS COLOR COLOR TEMP (PRESET / USER) GAMMA DISPLAY HORIZONTAL VERTICAL CLOCK PHASE OTHERS LANGUAGE POWER INDICATOR WHITE BALANCE FACTORY RESET...
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu Sub menu Description To adjust the brightness of the screen.
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu Sub menu Description HORIZONTAL To move image left and right. To move image up and down. VERTICAL CLOCK To minimize any vertical bars or...
On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Decrease : Increase : Select another sub-menu : Restart to select sub-menu NOTE If this does not improve the screen image, restore the factory default settings. If necessary, execute the WHITE BALANCE function again.
Menu. Press the MODE Button, then the main menu of the OSD appears. Menu Name E1910P Icons NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual.
On Screen Display(OSD) Selection and Adjustment Main menu When F-ENGINE is not NORMAL,CONTRAST can not be selected. E1910P E2210P E1910P E2210P E1910P E2210P Exit : Exit : Move : Select another sub-menu Sub menu Description NORMAL Select this when you want to use the product in the most general using environment.
On Screen Display(OSD) Selection and Adjustment (Only E2210P) Main menu Exit : Exit : Move : Select another sub-menu Sub menu Description WIDE Switch to full screen mode according to input image signal. Change the input image signal ratio to ORIGINAL original.
When PHOTO EFFECT is not NORMAL,CONTRAST can not be selected and COLOR is grey.When COLOR is selected down, PHOTO EFFECT is back to NORMAL and CONTRAST can be selected now. PHOTO EFFECT and F-ENGINE should not be unnormal at the same time. E1910P E2210P E1910P E2210P...
On Screen Display(OSD) Selection and Adjustment Main menu E1910P E2210P E1910P E2210P Exit : Exit : Move : Select another sub-menu Sub menu Description SEPIA This menu changes the screen to be Sepia tone (brown color). MONOCH This menu changed the screen to be Gray tone(black-and-white Picture) .
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the display connected? Is the power indicator light on? Is the power indicator flickering? Do you see an "OUT OF RANGE" message on the screen? Do you see a "CHECK SIGNAL CABLE"...
Troubleshooting Display image is incorrect Display Position is incorrect. On the screen background, vertical bars or stripes are visible. Any horizontal noise appearing in any image or characters are not clearly portrayed. IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed.
• Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lg.com. • Make sure to check if the video card supports Plug&Play function.
10 % to 80 % non-Condensing Temperature -20 ˚C to 60 ˚C Humidity 5 % to 90 % non-Condensing ), Detached ( O ) E1910P Without Stand Width 40.89 cm ( 16.10 inch) Height 33.81 cm ( 13.31 inch) Depth 5.82 cm ( 2.29 inch)
Specifications Display 55.8 cm (22 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 55.8 cm 0.282 x 0.282 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play DDC 2B(Digital),DDC2AB(Anlaog)
Specifications Preset Modes (Resolution) E1910P Display Modes (Resolution) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 E2210P Display Modes (Resolution)
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. After moving the product to face downward, make sure to place it on a soft cloth or a cushion to avoid surface damage.
Installing the Wall mount plate Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.
Make sure to read the Safety Precautions before using the product. Keep the OWNER’S MANUAL(CD) in an accessible place for furture reference. The model and serial number of the SET is located on the back or one side of the SET. Record it below should you ever need service.