1. Manuals
  2. Brands
  3. Woxcon Manuals
  4. Media Converter
  5. SCU31-TB
  6. User manual

Woxcon SCU31-TB User Manual

3x1 conference tabletop box with soft codec
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
SCU31-TB
3x1 Conference Tabletop Box with Soft Codec
All Rights Reserved
Version: SCU31-TB_2020V1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCU31-TB and is the answer not in the manual?

Questions and answers

Related Manuals for Woxcon SCU31-TB

Summary of Contents for Woxcon SCU31-TB

  • Page 1 User Manual SCU31-TB 3x1 Conference Tabletop Box with Soft Codec All Rights Reserved Version: SCU31-TB_2020V1.0...

  • Page 2: Table Of Contents

    3x1 Conference Tabletop Box with Soft Codec Table of Contents 1. Product Introduction ....................1 1.1 Features ......................1 1.2 Package List ....................... 1 2. Specification ........................ 2 3. Panel Description ......................3 4. System Connection ..................... 4 5. Panel Button Control ....................5 5.1 Signal Switching ....................

  • Page 3: Product Introduction

    3x1 Conference Tabletop Box with Soft Codec 1. Product Introduction The SCU31-TB 3x1 conference tabletop box is a multi-format switcher with two HDMI inputs, one USB Type-C input and one HDMI output. The USB Type-C port provides charging for source device up to 60w. The box supports HDMI and USB-C video resolutions up to 4K@60Hz 4:4:4 and multichannel audio.

  • Page 4: Specification

    3x1 Conference Tabletop Box with Soft Codec 2. Specification Input & Output Video Input (2) HDMI, (1) USB-C Video Input Connector (2) Type-A female HDMI, (1) USB 3.0 Type-C HDMI Input Resolution Up to 4K@60Hz 4:4:4 8bit, HDR 10, HDR 10+, Dolby Vision. USB-C Input Resolution Up to 4K@60Hz 4:4:4 Video Output...

  • Page 5: Panel Description

    3x1 Conference Tabletop Box with Soft Codec 3. Panel Description HDMI 1 USB-C HDMI 2 INPUT Tx Rx FIRMWARE HDMI IN 1 USB-C IN CHARGING HDMI OUT HDMI IN 2 RS232 DC 24V ETHERNET DEVICE TCP/IP DEVICE CONTROL ① INPUT SELECTION: Press the button repeatedly to cycle through the video inputs, and the corresponding input LED HDMI 1, USB-C or HDMI 2 will illuminate green.

  • Page 6: System Connection

    3x1 Conference Tabletop Box with Soft Codec ⑩ PC/HOST 1&2: Two USB Type-B ports for HOST PCs connection. The HOST PC can be controlled by the USB devices (e.g. mouse, keyboard, etc.) which are connected to four USB Type-A ports (DEVICE). ⑪...

  • Page 7: Panel Button Control

    3x1 Conference Tabletop Box with Soft Codec 5. Panel Button Control 5.1 Signal Switching Press INPUT button to select input source manually, the corresponding LED of HDMI 1, USB-C or HDMI 2 will illuminate green. Press and hold INPUT button at least three seconds to enable or disable auto switching mode, and the button will light up.

  • Page 8: Gui Control

    3x1 Conference Tabletop Box with Soft Codec 6. GUI Control The unit can be controlled via TCP/IP. The default IP settings are: IP Address: 192.168.0.178 Subnet Mask: 255.255.255.0 Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage: Username: admin Password: admin Type the user name and password, and then click Login to enter the section for video...

  • Page 9: Control Tab

    3x1 Conference Tabletop Box with Soft Codec 6.1 Control Tab 6.1.1 Signal Switching Video: Click button “HDMI 1”, “USB-C” or “HDMI 2” to select the corresponding input source. Auto Switching: ü Select 5V or TMDS signal detection mode. ü Click button “ON/OFF” to enable or disable auto switching mode. Power Off: Click the button to let the unit to enter standby mode, click the button again to wake up.

  • Page 10: Display Control

    3x1 Conference Tabletop Box with Soft Codec 6.1.2 Display Control Auto Display Control: Enable or disable the auto display control mode. In auto display control mode, the unit will automatically perform the following operations. ü System On: When the unit detects source signal input (5V or TMDS), or receives “Wake Up” command, it will automatically perform the following operation steps: Send “Display On”...

  • Page 11: Device Control

    3x1 Conference Tabletop Box with Soft Codec Display Setting tab or RS232 command. For more details, please refer to 6.2 Display Setting Tab or 7.4 Display Setting. Display: Click “On” or “Off” to turn on or off the display device by simultaneously sending CEC and RS232 commands.

  • Page 12: Display Setting Tab

    3x1 Conference Tabletop Box with Soft Codec 6.2 Display Setting Tab Baud Rate: Set the baud rate for display device. It supports 2400, 4800, 9600, 19200, 38400, 57600 and 115200. Command Ending: NULL, CR, LF or CR+LF can be selected. Select “Hex”...

  • Page 13: Edid Tab

    3x1 Conference Tabletop Box with Soft Codec No Activity Timeout: The system will enter standby mode, and the display device will be automatically shut down when no any activity is detected within the setup time. No Signal Timeout: The system will enter standby mode, and the display device will be automatically shut down when no source signal is detected within the setup time.

  • Page 14: Usb Host Tab

    3x1 Conference Tabletop Box with Soft Codec 6.4 USB Host Tab The system provides USB HOST PC 1, PC 2 or USB-C to be selected, and it provides four USB Type-A ports for connecting USB devices (e.g. mouse, keyboard, etc.) used to control the selected USB HOST.

  • Page 15: Tags Tab

    3x1 Conference Tabletop Box with Soft Codec 6.5 Tags Tab Modify the input source tags. 6.6 Network Tab Set Static IP or Dynamic Host Configuration Protocol (DHCP). Modify the static IP Address, Subnet Mask, and Gateway.

  • Page 16: Password Tab

    3x1 Conference Tabletop Box with Soft Codec 6.7 Password Tab Reset the login username and password. 6.8 GUI Upgrade Please visit at http://192.168.0.178:100 for GUI online upgrade. Type the username and password (the same as the GUI log-in setting, modified password will be available only after rebooting) to login the configuration interface.
  • Page 17 3x1 Conference Tabletop Box with Soft Codec...

  • Page 18: Rs232 Control

    3x1 Conference Tabletop Box with Soft Codec 7. RS232 Control The unit provides RS232 port for control device (e.g. PC) connection. After setting all needed input and output devices according to the system connection diagram, please install the RS232 control software (e.g. docklight) into the control PC to send RS232 command.
  • Page 19 3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Get the device standby or working #GET_POWER @POWER 0 status. Set GUI IP address. #SET_GUI_IP_ADDR #SET_GUI_IP_ADDR param1 = 0~255 192.168.0.179 param1.param2.param3.para param2 = 0~255 param3 = 0~255 @SET_IP 192.168.0.179 param4 = 0~255 #GET_GUI_IP_ADDR...

  • Page 20: Signal Switching

    3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback 4 - 9600 5 - 4800 #SET_RS232_BAUD 4 6 - 2400 #SET_RS232_BAUD 5 #SET_RS232_BAUD 6 @RS232_BAUD 0 @RS232_BAUD 1 @RS232_BAUD 2 @RS232_BAUD 3 @RS232_BAUD 4 @RS232_BAUD 5 @RS232_BAUD 6 #GET_RS232_BAUD Get the RS232 baud rate.
  • Page 21 3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback #GET_AUTO_SWITCH Get the source switching mode. @AUTO_SWITCH 0...

  • Page 22: Display Control

    3x1 Conference Tabletop Box with Soft Codec 7.3 Display Control Command Example and Command Function Feedback Enable the auto display control @OPEN CEC DISPLAY #AUTO_CEC_SET_PANEL_O mode. For more function ON/OFF WHEN description, please refer to the SIGNAL/NOSIGNAL 6.1.2 Display Control. @CLOSE CEC DISPLAY #AUTO_CEC_SET_PANEL_C Disable the auto display control...

  • Page 23: Display Setting

    3x1 Conference Tabletop Box with Soft Codec 7.4 Display Setting Command Example and Command Function Feedback Set the “Display On” command “xxxx” to be saved. When pressing #SET_ON_A_1:ABCDEFG the “DISPLAY ON” button on front #SET_ON_H_1:11 22 33 panel, the command will be automatically sent to the display device.
  • Page 24 3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Set the “Display Input Select” #SET_DIS_SEL_A_1:ABC command “xxxx” to be saved. The DEFG command is usually used to select #SET_DIS_SEL_H_1:11 input source for display device. 12 13 param1 = A, H #SET_DIS_SEL_param1_par §...

  • Page 25: Edid Setting

    3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Get the No Activity Timeout. The @DELAY TIME TO %d display device will be automatically MINUTES, TO TURN OFF #GET_NO_ACT_TIME shut down when no any activity is DISPLAY WHEN NO detected within the setup time.
  • Page 26 3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback EDID BYPASS 1280x720@60Hz Stereo Audio 1920x1080@60Hz 8bit Stereo Audio 1920x1080@60Hz 8bit High Definition Audio 1920x1080@60Hz 3D Stereo Audio 1920x1200@60Hz 8bit Stereo Audio 3840x2160@30Hz 8bit Stereo Audio 3840x2160@30Hz 8bit High Definition Audio @H1_EDID_MODE 1 3840x2160@30Hz Deep...

  • Page 27: Usb Control

    3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback 1 - Upload the user-defined EDID 1. @USER_EDID_READY 1 2 - Upload the user-defined EDID 2. USER EDID 1 UPLOAD @USER_EDID_READY 2 USER EDID 2 UPLOAD 7.6 USB Control Command Example and Command Function...

  • Page 28: Firmware Upgrade

    3x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Get the mapping relationship when #GET_USB_MAP the USB HOST follows the input #GET_USB_MAP H1 #GET_USB_MAP H2 video source switching. param1 = H1, H2, Null #GET_USB_MAP param1 § H1 - HDMI 1 IN @H1_USB_MAP PC1 H2 - HDMI 2 IN...

Table of Contents