Related Manuals for Woxcon NPG-DA24T
Summary of Contents for Woxcon NPG-DA24T
- Page 1 User Manual NPG-DA24T KIT 18G HDMI 2x4 Splitter Kit over CAT5e/6/7 All Rights Reserved Version: NPG-DA24T KIT_2020V1.1...
-
Page 2: Table Of Contents
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 Table of Contents 1. Product Introduction ....................1 1.1 Features ......................1 1.2 Package List ....................... 2 2. Technical Specification ....................3 2.1 Splitter ........................ 3 2.2 Receiver ......................4 3. Panel Description ......................6 3.1 Splitter Front Panel ..................... -
Page 3: Product Introduction
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 1. Product Introduction Thanks for choosing this 2x4 HDMI Splitter Kit over CATx cable! This device distributes either one of two HDMI inputs to one HDMI and four CATx outputs. The splitter is designed with an IR loop out which is intended to cascade to additional units. -
Page 4: Package List
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 1.2 Package List 1x NPG-DA24T 2x4 HDMI Splitter over CATx 4x Plastic Cushions 1x RS232 Cable (3-pin to DB9) Splitter 1x IR Cable (3.5mm to 3.5mm, used for IR cascade) 4x IR Receivers... -
Page 5: Technical Specification
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 2. Technical Specification 2.1 Splitter Video Input (1) HDMI Input Input Connector (1) Female type A HDMI HDMI Input Resolution Up to 4K@60Hz 4:4:4 8bit Video Output (1) HDMI, (4) CAT Output Output Connector (1) Female type A HDMI;... -
Page 6: Receiver
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 Control (1) EDID, (1) FIRMWARE, (1) IR ALL IN, (4) IR IN, (1) IR LOOP Control port OUT, (1) IR OUT, (1) RS232 IN (1) 3-pin DIP switch, (1) USB-A, (7) 3.5mm mini jacks, (1) 3-pin Control Connector terminal block General... - Page 7 18G HDMI 2x4 Splitter Kit over CAT5e/6/7 HDCP Version 2.2, 1.4 compliant Bidirectional PoC Support HDMI 2.0 Cable Length 4K@60Hz 4:4:4 ≤ 5m, 4K@60Hz 4:2:0 ≤ 10m, 1080p ≤ 15m Transmission Distance 4K ≤ 70 meters (230ft), 1080p ≤262 feet (80 meters) Operation Temperature -5~ +55℃...
-
Page 8: Panel Description
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 3. Panel Description 3.1 Splitter Front Panel HDMI 1 HDMI 2 SELECT DEFAULT H.RES L.RES 1. POWER LED: Illuminates green when power is applied. Blinks when the device is in standby mode. Off when power is off. 2. -
Page 9: Splitter Rear Panel
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 3.2 Splitter Rear Panel 1. HDMI INPUT: Connects to HDMI source device. 2. OUTPUTS: HDMI: Type-A female HDMI port to connect local HDMI display device. CATx 1~4: RJ45 port to connect the CATx IN port of receiver by CATx cable. It supports 12V PoC to power the receiver. -
Page 10: Receiver Panel
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 3.3 Receiver Panel 1. DISPLAY: Type-A female HDMI port to connect HDMI display device. 2. CATx IN: RJ45 port to connect the CATx OUT port of transmitter by CATx cable. It supports 12V PoC and the receiver can be powered from the transmitter. The orange LED illuminates when there is a valid HDMI signal input. -
Page 11: System Connection
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 4. System Connection 4.1 Usage Precaution Make sure all components and accessories included before installation. System should be installed in a clean environment with proper temperature and humidity. All of the power switches, plugs, sockets, and power cords should be insulated and safe. -
Page 12: Source Switching
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 5. Source Switching 1) Press the SELECT button to switch to next source device, and then the corresponding input LED will turn green. 2) Press and hold the SELECT button at least 3 seconds to enable auto switching mode, and it abides by the following principles: The switcher will switch to the first available active input starting at HDMI IN 1>... -
Page 13: Ir Control
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 7. IR Control The IR receivers and emitters can be connected to the system to allow for IR control of remote devices. The bidirectional IR feature provides the two-way control either for the source or display device(s). -
Page 14: Controlling The Source Device
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 7.3 Controlling the Source Device The IR OUT port of the splitter can send all IR signals to control source device. Connect four IR receivers to IR IN ports on receivers, and then connect an IR emitter to IR OUT port of the splitter. -
Page 15: Rs232 Control
In the commands, “[”and “]” are not needed to be typed in actual operation. Type the command carefully, it is case-sensitive. 8.1 System Commands Command Example and Command Function Feedback >SetDeviceModel: NPG-DA24T >SetDeviceModel:XXXX Set the product’s name. <Model:NPG-DA24T >GetDeviceModel Get the product’s name. <Model:NPG-DA24T >SetDeviceModelRst... - Page 16 18G HDMI 2x4 Splitter Kit over CAT5e/6/7 Command Example and Command Function Feedback 02 – HDMI input2. >GetVideo >GetVideo Get the current input source. <Video 01 Enable or Disable auto switching. >SetAutoSwitch On >SetAutoSwitch Param = On, Off [Param] On – Enable <AutoSwitch On Off - Disable >GetAutoSwitch...
-
Page 17: Cec Commands
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 Command Example and Command Function Feedback >GetSystemPowerMode >GetSystemPowerMod Get the system power status. <SystemPowerMode On Set the baud rate of splitter. >SetRS232Baud 115200 param = 115200 >SetRS232Baud 57600 [Param] 38400 <SetRS232Baud 115200 19200 9600 >GetRS232Baud Get the baud rate of splitter. - Page 18 18G HDMI 2x4 Splitter Kit over CAT5e/6/7 02 – HDMI2 Send CEC BACK command to >SetCecSrcBack >SetCecSrcBack 01 source device. [Param] Param = 01, 02 <CecSrcBack 01 01 – HDMI1 02 – HDMI2 Send CEC ENTER command to >SetCecSrcEnter >SetCecSrcEnter 01 source device.
- Page 19 18G HDMI 2x4 Splitter Kit over CAT5e/6/7 02 – HDMI2 Send CEC NEXT command to >SetCecSrcNext >SetCecSrcNext 01 source device. [Param] Param = 01, 02 <CecSrcNext 01 01 – HDMI1 02 – HDMI2 Send CEC REWIND command to >SetCecSrcRewind >SetCecSrcRewind 01 source device.
-
Page 20: Edid Management
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 9. EDID Management The Extended Display Identification Data (EDID) is used by the source device to match its video resolution with the connected display. By default, the source device obtains its EDID from the first connected display. Meanwhile, since the displays with different capabilities are connected to the splitter, the 3-pin DIP switch on the front panel can be used to set the EDID to a fixed value to ensure the compatibility in video resolution. -
Page 21: Firmware Upgrade
18G HDMI 2x4 Splitter Kit over CAT5e/6/7 10. Firmware Upgrade Please follow the below steps to upgrade firmware by the USB-A port: 1) Prepare the latest upgrade file (.bin) and rename it as “FW_MERG.bin” on PC. 2) Power off the splitter and connect the Micro-USB ( ) port of splitter to the FIRMWARE PC with USB cable.
Need help?
Do you have a question about the NPG-DA24T and is the answer not in the manual?
Questions and answers