Removable electric motorization for wheelchair (46 pages)
Summary of Contents for Acekare Yomper
Page 1
Make your life easier ! Yomper Removable electric motorization for wheelchair Set up guide for the frame on foldable wheelchair with braces v1.3 - 23/02/2017 1 / 17...
2.7 Step 7 : Check the height between the frame’s axis and the ground ....13 2.8 Step 8 : Check the space for the insertion of the Yomper ....... 13 2.9 Step 9 : Check the adjustment of the stop (H) ..........14...
1 Presentation of the frame The fixing frame of the Yomper is already assembled when it’s delivered. It is to be set up on foldable wheelchairs equipped with braces : It is composed of the following parts : 2 loops (A et A') •...
Page 5
The 2 loops (A et A’) will be fixed on the frame of the wheelchair. All the screws and bolts necessary to set up the frame are already in place : 2 round head screws M6 x 50 (1) • 3 round head screws M6 x 40 (2) •...
Setting up the frame 2.1 Step 1 : Open the frame and lock it in the clip (B) 2.2 Step 2 : Protect the frame of the wheelchair with the tape supplied Protect the frame at a distance of 110mm from the wheels’ axis : 6 / 17...
2.3 Step 3 : Measure the distance from the ground to the axis of the frame’s tube The measurement must be made at the level of the protection that you set up during step 2 : 2.4 Step 4 : Setting up the right loop (A') 7 / 17...
Check out the chart below to know in which holes you must put the screws. Screws in the holes 210 à 220mm 1 et 1' 220 à 230mm 2 et 2' 230 à 240mm 3 et 3' 240 à 250mm 4 et 4' 2.4.1 Unscrew the indexing digit (L) Before screwing the loop on the right, you need to unscrew the indexing digit (L) to...
2.4.2 Unscrewing the 2 screws (2) and setting up the right loop on the right side of the frame The loop must come at the level of the space protected with tape : Put back into place the 2 washers M6 (6) on the lower screw, between the 2 parts of the loop 2.4.3 Put back the indexing digit 9 / 17...
2.5 Step 5 : In the same way, set up the left loop To reach the 2 screws (1), remove the spring (K) and the Nylstop screw M6 (7) : Put the spring back (K) and the Nylstop screw M6 (7). 2.6 Step 6 : Close the frame and measure the distance L You may have to add washers between D and G, and between F and G’...
Page 12
Check out the below chart to know how many washers you need to add : Washers’ thickness Washers’ thickness Between F and G’ between D and G 10mm etc..If necessary, add the washers between D and G, and between F and G’ : Tighten very strongly the 2 locknuts (G) and (G’) with the spanner supplied: Tighten lighly the 2 black Nylon washers (5) with a multi-socket pliers : 12 / 17...
180mm : If it’s not the case, begin again at step 5. 2.8 Step 8 : Check the space for the insertion of the Yomper You should find 122mm between the 2 black Nylon washers (5): If it’s not the case, adapt the number of washers between D and G, and between F and G’...
The stop (H) prevents the Yomper from making the wheelchair topple backwards. It needs to be perfectly adjusted for the safety of the user. The Yomper’s and frame’s stops must touch when the front wheels of the wheelchair are lifted 120mm above the ground.