GE StayBright 16123 Quick Start Manual

16123LC
For indoor use only
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
a)
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
o)
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place
on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or
frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including tree,
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections,
and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
CAUTION:
1. To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or
branch coverings of metal or materials which look like metal, and b) Do not mount or support
strings in a manner that can cut or damage wire insulation.
2. Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one
lamp burns out. Replace lamps only with the spare lamps provided with this product.
USER SERVICING INSTRUCTIONS
Replace the lamp.
1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling cord.
2. Pull lamp and plastic base straight out of lampholder.
3. Replace lamp with only 3.3 Volt, 20 mA LED type lamp
(provided with product).
To reduce the risk of overheating replace burned-out lamps promptly. Use 3.3 Volt, 20 mA lamps only.
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps in the
light set so that the leads will touch the contacts inside the lampholder.
CAN ICES-005(B) / NMB-005(B)
For questions and /or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com
© 2018 Nicolas Holiday Inc., 204 Spring Hill Road Trumbull, CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
If the product One or more of the based LEDs
does not light may have loosened from the socket
during transporting. There is a break
in the circuit between the LED leads
and the socket terminals.
Male/female connectors not fully
inserted together. Non working
control box. Foot pedal in off
position.
If a based LED One or more of the based bulbs
is missing may have come out of the socket
when transporting.
If an LED fails Incorrect LED, premature LED
to light (shorts failure or voltage is too high.
or opens)
LEDs fail to Defective control box
switch from
white to multi
FP-18 PRINTED IN CHINA
CORRECTIVE ACTION
Unplug the set at the outlet. Starting with the
first unlit LED, gently push (don't twist) each
LED base firmly into the socket. If still does
not light, then remove each based LED and
check for out of place lead wires. Make
certain connectors fully inserted and securing
cap fully tightened. Step on foot pedal to turn
LEDs on.
Mark socket(s) with a piece of tape and
unplug the set. Replace the based LED or
use one of the spare based LEDs included
with product.
The LED may be out or dimly lit. Replace
bad LEDs as soon as you find them.
Contact Customer Support.