Related Manuals for Harvest TEC 600
Summary of Contents for Harvest TEC 600
- Page 1 Operation Manual Model 600 Moisture Sensor Kit for Large Square Balers Forage Harvester 600-16-OPR-BLE 12/19...
- Page 2 (intentionally blank)
-
Page 3: Table Of Contents
Harvest Tec Model 600 Operations Table of Contents Page Introduction Safety Safety Decals Operation Turn On / Off iPad Downloading Harvest Tec app iPad Integration Control Module iPad Integration Control Light Signals Bluetooth Receiver Lights Shutting down the Hay App... -
Page 4: Introduction
System has been designed to be operated through an Apple iPad (not included) using the Hay App. As well as the option to plug directly into most tractors that have an ISOBUS Monitor. The 600 Moisture Monitoring System offers these advantages by operating through an Apple iPad: 1. -
Page 5: Operation
4. Select an available network when detected by the iPad, shown in area above that currently says ‘Other.’ 5. Select App Store icon (below) and open. *You will need a Wi-Fi connection available to view App Store. **The Harvest Tec system WILL NOT appear under the Bluetooth tab in the Setting App. -
Page 6: Ipad Integration Control Module
Green Light – The Bluetooth receiver is connected to the Hay App. **600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest Tec for a required update in order to use the iPad Integration Module (030-6672C). -
Page 7: Shutting Down The Hay App
Shutting Down the Hay App To shut down the Hay App double click the home button (Figure A). This will show the open apps that are running on your iPad (Figure B). *Note: By pressing the home button one time to return to the home screen, the Hay App does not shut down. The system will however, stop applying preservative after 10 seconds. -
Page 8: Operating The Hay App
Operating the Harvest Tec iPad App When ready to operate your applicator system, open the Hay App on the iPad by selecting the Hay App icon. Device Selection The app will open to the Device Menu screen as shown below. -
Page 9: Manual Selection
Operating the Harvest Tec iPad App (continued) Manual Selection Selecting the Manual button (below) displayed to the right of the baler name will open the operation manual for your baler. *Use the following information for Large Square Balers. *You do not need to be connected to a baler to open the manual after a baler has been connected. -
Page 10: Tab Descriptions
Operating the Harvest Tec iPad App (continued) Tab Descriptions Automatic Mode: This mode allows you to use all of the applicator features such as adjusting preservative application on the go and counting total pounds of product used. Manual Mode: Allows operator to manually turn pumps on and off. This mode also has moisture content displayed. -
Page 11: Screen Menus
Screen Menus Use the screen shots below to navigate through the operation screens. Automatic Mode Bluetooth Connection Indicator Green -DCP is connected Yellow -DCP connecting -DCP not connected # Used will display 0 with moisture only systems Manual Mode Bluetooth Connection Indicator Green -DCP is connected Yellow... -
Page 12: Setup Mode
Setup Mode – Large Square Balers NEEDS TO BE U PDAT ED *Only used if equipped with Tagger Indicates tagger is ON Turn Tagger ON by selecting the *If RFV Equipped, additional options If using RFV Spray Module, Indicates Spray Module is ON will appear on Bale ID Screen (next) turn ON by selecting the Make sure Knotter/Dye Tip... - Page 13 Setup Mode – Large Square Baler (continued) *Select X to turn on options shown Indicates Crop Eyes are ON *Only used if equipped with GPS *Select grey area to change *Select appropriate GPS unit *Ensure pump module is shut off X indicates module is off...
- Page 14 Setup Mode – Large Square Baler (continued) *Select correct bale weight, length, *Turn on Bale Rate sensor, and time per bale information Green bar indicates sensors are ON *Ensure all baler sensors are turned OFF *If using a scale kit, turn sensor ON...
-
Page 15: Setup Mode If Rfv Equipped
Setup Mode – Large Square Baler (If RFV Equipped *Select correct bale weight, length, *Turn on Bale Rate sensor, and time per bale inforation Green bar indicates sensors are ON *Select correct bale size Software Versions *Versions shown are examples (will not match your applicator) -
Page 16: Job Records
Job Records Type desired Field Name, select Create Job *When RFV Equipped, Average RFV, Ave TDN/CA90% info will be added For Bale details select Bale Button Use arrows to change jobs shown... - Page 17 Job Records (continued) Select Download when wanting to Use arrows to change jobs shown. Pressing the Select or Select All tab to download job records to USB Stick Indicates selected jobs choose which job to download or delete The Export allows you to send an email a When the Export page is opened the bale When all bales have been retrived, Export file with selected job records...
-
Page 18: Setting Up System For Initial Use
Baling Rate Settings – Large Square Balers After pushing the SETUP MODE key in the Main Menu screen, the screen on the left will appear: 1. On the setup mode screen press the BALING RATE key. 2. Press the grey number value to the right of AVG Bale Weight (Lbs). To adjust the weight of your bales, the scroll tool shown on the right will display. -
Page 19: Rfv Setup
RFV Setup Use the information below when your applicator is RFV Equipped. *Only available on large square balers. 1. Select the RFV Setup tab on the Baling Rate Setup Screen. 2. Select the correct height and width of bale by selecting the grey area. All values can be changed. 3. -
Page 20: Operation Instruction
Operation Instructions Automatic mode will allow you to view the moisture information, bale rate, last bale moisture and tons baled. Automatic Mode After pushing the AUTOMATIC MODE key in the Main Menu screen, the following screen will appear: RFV Equipped 1. -
Page 21: Manual Mode
Manual Mode Manual mode can be used to view the moisture information, bale rate, last bale moisture and tons baled. After pushing the MANUAL MODE key in the Main Menu screen, the following screen will appear: RFV Equipped 1. To pause the unit during operation select the Pause key. 2. -
Page 22: Job Records
Job Records After pushing the JOB RECORDS key in the Main Menu screen, the following screen will appear: *When RFV Equipped, Average RFV, Ave TDN/CA90% info will be added 1. The job number will be displayed at the top center. The current job being viewed will always read "Job #: 0". - Page 23 Download Job Records After pushing the JOB RECORDS key in the Main Menu screen, the following screen will appear: Prior to downloading job records a USB stick will need to be placed into the USB port on the applicator’s Dual Channel Processor (DCP).
-
Page 24: Export Job Records (Emailing Records)
Export Job Records (emailing records) 1. To export the Job Records through an email or save to the iPad select the Export button 2. The list of job records you have created, will display in the middle of the screen and the individual bale information will begin to download automatically. -
Page 25: Export Job Records (Saving To Ipad)
Export Job Records (saving to iPad) 1. To export the Job Records through an email or save to the iPad select the Export button 2. The list of job records you have created, will display in the middle of the screen and the individual bale information will begin to download automatically. -
Page 26: Wiring Diagram
The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty. IF MODIFICATIONS ARE REQUIRED CONTACT HARVEST TEC FIRST! b. This unit will not function on positive ground tractors. -
Page 27: Common Questions
Hay App connection on the Apple iPad.Red Light – The Bluetooth receiver has power. Green Light – The Bluetooth receiver is connected to the Hay App. 9. Can the Harvest Tec 600 be updated for preservative or a tagger? Yes. Consult your local dealer for part numbers and pricing. -
Page 28: Troubleshooting
5. Short in wire between star wheels & DCP. 5. Replace wire. 6. Check hay with hand tester to verify. 6. Contact Harvest Tec if continued Moisture readings 1. Test bales with hand tester to verify that erratic. -
Page 29: Ipad Troubleshooting
Refer to your iPad owner’s manual or contact apple How do I send in my iPad for service? customer service. DO NOT SEND iPad TO HARVEST TEC. For other issues refer to your iPad Owner’s Manual or contact Apple Directly *Harvest Tec Does Not Service iPads *... -
Page 30: Pin Outs
Pin Outs Power/Comm Harness 006-6650TM at Hitch Pin 1 Red +12V Power to TSD Pin 2 Red +12V Power to DCP Pin 3 Orange Keyed Power Pin 4 Gray Shield Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Orange Can1 Hi Pin 8 Black... - Page 31 Pin Outs (continued) Main Power Connector on DCP Pin 1 Red +12V Power from tractor Pin 2 Black Ground from tractor Pin 3 Orange Keyed power Star Wheel and Bale Rate Sensor connector on DCP Pin 1 Blue +12V Power Pin 2 Orange Ground Pin 3 Black...
-
Page 32: Parts Breakdown
Parts Breakdown for Star Wheel Moisture Sensors Description Part# Description Part# Block cover 006-4641B Star wheel block 006-4641A Electronic swivel 006-4642A Star wheel sensor 030-4641C Swivel insert w/ Ref # 10 Twine guard-left 001-4645 Snap ring (per side) 006-4641K Twine guard-right (prox) 001-4644 Washer (per side) w/006-4641K... -
Page 33: Controls & Harness
Parts Breakdown for 600 Series Control and Harnesses Dual Channel Processor (DCP) Ref Description Part Number Dust Plugs 006-5651PLUGS End of Bale Sensor 600 Series 006-7400 Hesston 4755, 4910 EOB Mount 001-4648H EOB Bracket CLAAS 3300 001-4648C Krone EOB Bracket... -
Page 34: Optional Ipad Display Kit
Optional iPad Display Kit (030-4670DK) Description Part # Ref Description Part # Suction cup mount 001-2012SCM iPad Mini Charger 12V 001-2012P Ram mount 001-2012H iPad Mini 4 case 001-2012C4 ® iPad Mini spring load 001-2012SLC iPad Mini 4 006-4670IP cradle (Mini 4) 16 gauge power wire 006-4723P 4 amp fuse... -
Page 35: Warranty Statement
Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. - Page 36 HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.com...