Waterco Solclear 90 Operating Instructions Manual

Solclear uv sterilizer

Advertisement

Quick Links

SOLCLEAR UV STERILIZER
Operating
Instructions
Manual
WARNING
This equipment must be installed and serviced by a qualified technician.
!
Improper installation may result in property damage, serious injury or death.
Improper installation and/or operation will void the warranty.
Notice to Installer
This manual contains important information about the installation, operation
and safe use of this product. Once the product has been installed this manual
must be given to the owner/operator of this equipment.
www.waterco.com

Advertisement

Table of Contents
loading

Summary of Contents for Waterco Solclear 90

  • Page 1 Improper installation and/or operation will void the warranty. Notice to Installer This manual contains important information about the installation, operation and safe use of this product. Once the product has been installed this manual must be given to the owner/operator of this equipment. www.waterco.com...
  • Page 2 9000 2040T x 77 (6.9bar) Solclear Input Voltage: 230 VAC (190-260VAC) / 50-60Hz General View of Solclear 90 End View End View Distance between inlet & outlet Overall length excluding lamp lead wire General View of Solclear 150 End View End View Distance between inlet &...
  • Page 3: Installation Diagram

    Solclear UV Sterilizer I 03 NOTES: 1. Do not allow Solclear UV sterilizer to freeze. 2. Recommended ambient temperature: 2°C-40°C (36°F-104°F). 3. Input voltage is 230VAC (190-260VAC) / 50-60Hz. 4. Maximum recommended operating pressure is 100psi (6.9bar). 5. The system and installation shall comply with applicable state and local regulations. INSTALLATION DIAGRAM Elbow Pressure switch...
  • Page 4 04 I Solclear UV Sterilizer SOLCLEAR 300 Quartz Flow Lamp Ballast Lamp Thimble Wattage Standard Operating Rate Size Life Model Size Lamp Ballast Pressure gpm lpm hour Solclear T6125 450 x 350 88.5psi 300 D30 x 910 125W UV-24 13,000 (212564) x 205 (6.1bar)
  • Page 5 Solclear UV Sterilizer I 05 NOTES: 1. Do not allow Solclear UV sterilizer to freeze. 2. Recommended ambient temperature: 2°C-40°C. 3. Input voltage is 230VAC / 50-60Hz. 4. Maximum recommended operating pressure is 88.5psi (6.1bar). 5. The system and installation shall comply with applicable state and local regulations. INSTALLATION DIAGRAM Pressure switch...
  • Page 6 06 I Solclear UV Sterilizer ASSEMBLY Solclear 90 & 150 WARNING Germicidal ultraviolet rays are harmful to eyes & skin. CAUTION: Ultraviolet lamp and quartz sleeve are easily damaged. Pay attention when removing or replacing lamp and quartz sleeve. Solclear 90...
  • Page 7 Solclear UV Sterilizer I 07 ASSEMBLY Solclear 300 WARNING Germicidal ultraviolet rays are harmful to eyes & skin. CAUTION: Ultraviolet lamp and quartz sleeve are easily damaged. Pay attention when removing or replacing lamp and quartz sleeve. ITEM DESCRIPTION Solclear 300 (Part No.) Water Proof Strainer 725110456 PVC Nut...
  • Page 8: Installation

    08 I Solclear UV Sterilizer INSTALLATION: 1. Install Solclear UV sterilizer in a readily accessible and well-lit location to facilitate inspection and maintenance. 2. Inspect for hidden electrical wiring or plumbing prior to drilling holes. 3. Attach mounting clips to the wall. 4.
  • Page 9: Maintenance

    • Quartz sleeve is to be replaced every 24 months. II. UV lamp replacement is recommended every 8,000-9,000 hours (approximately 12 months for continous service) for Solclear 90 & 150, or 13,000 hours (approximately 1.5 years of continous service) for Solclear 300 of operation.
  • Page 10: Electronic Ballast

    10 I Solclear UV Sterilizer Electronic Ballast (for Solclear 90 & 150 only) General View of Ballast UVC-2040T 112.6 76.97 Features & Functions 1. Auto Timer Function 4. Display for UV Lamp Status 2. Constant Current Limited Power Output 5. Status Signal Output 3.
  • Page 11: Installation Instruction

    Solclear UV Sterilizer I 11 Installation Instruction The ballast has 3 ports: 1. Dry contact signal output port 2. Power input port 3. Lamp output port 1. The no. 1 port is a relay dry contact output. When the ballast is working normally, the dry contact is shorted, otherwise the dry contact is open.
  • Page 12 SA/NT - ADELAIDE Auckland, New Zealand Nehsons Building, Singapore : +61 8 8244 6000 : +64 9 525 7570 Tel : +65 6344 2378 ACT DISTRIBUTOR : +61 2 6280 6476 Waterco Limited ABN 62 002 070 733 (W99400) 07/2021...

This manual is also suitable for:

Solclear 150Solclear 300Uvc-2040t

Table of Contents