Subscribe to Our Youtube Channel
Related Manuals for Taga TTA-1000B
Summary of Contents for Taga TTA-1000B
- Page 1 TTA-1000B HIGH-END VACUUM TUBE INTEGRATED AMPLIFIER Instruction Manual Edition 04-2021...
- Page 2 Introduction Thank you for purchasing this TAGA Harmony amplifier. TTA-1000B is a 2 x 30W / 8ohm Pure Class A high-end vacuum tube integrated amplifier utilizing high-performance PSVANE vacuum tubes from the Classic series: KT88 tubes in the output stage (with the fixed grid load) and a ECC83 tube preamp section, composed of 6SN7 long-tail phase inversion drive circuit.
-
Page 3: Table Of Contents
Contents Safety Instructions Remote controller Front and Rear Panel Hooking Up Speaker Cables Hooking Up the Amplifier Operation Bluetooth Connection ® Additional Information Specifications Kit content... -
Page 4: Safety Instructions
Safety Instructions IMPORTANT READ THIS SECTION CAREFULLY BEFORE PROCEEDING! WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The triangle containing a lightning symbol is intended to alert the user to the presence of uninsulated dangerous voltages within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - Page 5 Safety Instructions 1. Read Instructions - All the safety and operating instructions 13. Overloading - Do not overload wall outlets, extension cords or should be read before the product is operated. integral convenience receptacles as this can result in a risk of fire 2.
-
Page 6: Remote Controller
Remote Controller • Always use AAA batteries and do not use the rechargeable batteries. • Do not mix new batteries with old batteries or different kinds of batte- ries. • If the batteries run out, remove the old batteries and replace them with new ones within several minutes. -
Page 7: Front And Rear Panel
Remote Controller 1. CD Input Selector Button 2. Line Input Selector Button 3. Phono MM Input Selector Button 4. Bluetooth Input Selector Button ® 5. Phono MC Input Selector Button 6. Mute Button 7. Volume Buttons (▼/▲) Front and Rear Panel Front Panel: 1. - Page 8 Front and Rear Panel Rear Panel: Phono Ground Screw Analog Stereo RCA Inputs PHONO (MM / MC) / LINE / CD Preamplifier Stereo RCA Output 10. Speaker Right Channel Output (Speaker Connectors) 11. Speaker Left Channel Output (Speaker Connectors) 12. Power Cable Input and Fuse Box A blown fuse should be only exchanged for exactly the same type as indicated on the rear panel.
-
Page 9: Hooking Up Speaker Cables
Hooking Up Speaker Cables The Speaker Connectors can accommodate up to 10AWG speaker cables as well as most of popular plugs (banana etc.). It is recommended to leave about 150 cm (5 feet) of extra cable at the amplifier end to facilitate positioning and installation of the amplifier. -
Page 10: Hooking Up The Amplifier
Hooking up the Amplifier Turntable Right speaker Left speaker (MM or MC) FM/AM tuner etc. CD Player, etc. Interconect RCA Phono Interconnect RCA Speaker cables Interconnect RCA External power amplifier, powered speakers, etc. Smartphone, tablet, etc. - Page 11 ® Note! Make sure the antenna is securely and firmly installed - otherwise the “TTA-1000B” Bluetooth device may not be found or connection may be unstable. ® 3. Using speaker cables (not supplied with this product) connect your speakers to the SPEAKERS OUT connectors located on the rear panel.
-
Page 12: Operation
Operation 1. Plug the Power Cable to the amplifier and into the wall outlet. 2. Turn on the amplifier – press the Power Switch (the Power Switch The CD Input LED Indicator will be blinking and should turn on in approximately 30 seconds. -
Page 13: Bluetooth ® Connection
Bluetooth devices. ® 4. After a short time “TTA-1000B” will appear on the screen of your audio source. 5. Select “Pair” on your audio source to connect with the amplifier. After connection is successful the Bluetooth Input LED Indicator will be illuminated ®... -
Page 14: Additional Information
Additional Information Break-In Your TAGA Harmony amplifier sounds great immediately after it is taken out of the carton but as all vacuum tube amplifiers, this amplifier requires a “break-in” period to reach its full sonic capabilities. During the “break-in” period it is recommended to operate the amplifier at moderate volume levels. - Page 15 Only the output power tubes (KT88) need to be biased manually. This procedure requires to open the amplifier and we recommend to contact TAGA Harmony authorized service center to perform it. The bias procedure has to be always performed in case: - If any output power tube (KT88) is changed for another one (e.g.
-
Page 16: Specifications
Specifications Power Output 2 x 30W Class A Output impedance 4ohm, 8ohm Vacuum Tubes PSVANE Classic Series 4 x KT88, 2 x 6SN7, 1 x ECC83 Triode operation mode ≤0.35% (1KHz/2V) Signal/Noise ratio ≥89db Frequency Response 10Hz – 30kHz (+/- 1dB) Inputs Analog: RCA Stereo: CD, Line, Phono (MM/MC) Outputs... - Page 17 Notes...
- Page 18 Notes...
- Page 19 Notes...
-
Page 20: Kit Content
We strongly advise to contact a professional installer or dealer in order to install TAGA Harmony products. We recommend using high quality TAGA Harmony cables and other installation accessories. Kit Content: Amplifier 1 EA Remote Controller 1 EA Bluetooth Antenna 1 EA ®...
Need help?
Do you have a question about the TTA-1000B and is the answer not in the manual?
Questions and answers