FRONT CONTROLS 4 User interaction inputs: 4 User interaction outputs: 4 REAR CONNECTIONS 5 REMOTE 6 SET UP OPERATION 6 OLED DISPLAY 7 VOLUME CONTROL 8 Controls 8 Process & Indicators 8 INPUT SELECTION 8 TRACK FUNCTIONS 9 Control 9 Process &...
F R O N T C O N T R O L S User interaction inputs: • RGB LED button • Manual buttons (Previous, Play/Pause & Next) • Rotary dial • Headphone socket • Roksan app • BluOS app User interaction outputs: •...
2. Turntable Grounding Post Used to ground the tone arm attached to the turntable 3. Phono Input Connect the output from the turn table to the Attessa Streaming Amplifier 4. Analogue 1 Input Connect and analogue source 5. Analogue 2 Input (music sense) Connect a second analogue input.
R E M O T E Remotefeedback:AllactionshavetheremoteLEDflashonandoff. S E T U P O P E R A T I O N 1. Standby A single press of the RGB LED button or single press of the standby/power button on the remote and RGB LED goes solid red. 2.
3. Load/warm up phase Roksan logo to appear when product goes into power mode. 4. BLE pairing mode: During set up mode via the app the BLE passkey appears on the screen. O L E D D I S P L A Y The inputs available on the streamer are scrolled through using the encoder or remote and are displayed using the following icons: Digital 5 (BluOS)
V O L U M E C O N T R O L Controls • Rotary dial • Remote • BluOS app Process & Indicators • Incremental increase: clockwise turn of rotary dial or single press of remote + button. LED strip will illuminate more coloured bars. •...
T R A C K F U N C T I O N S Control • Manual buttons • Remote • BluOS app Process & Indicators Track functions are only applicable for the Bluetooth input & BluOS inputs. 1. Pause: a single press of the play/pause button (remote or manual button) and the dual LED’s to flash on.
Page 10
11. Repeat once: triple press of SRR remote button. OLED to display repeat once icon. Note:Ifthefirstactionistopresstrackforwardortrackbackthiswillautomatically complete the function and then play the track all in one step.
• Roksan app • BluOS app Set-Up • BluOS Attessa set-up: BluOS Indicators • MQA status: When a track uses MQA services the OLED is to display the MQA or MQA studio icon. • Hotspot mode: RGB LED is solid green.
• R eceivingIRcodes:RGBLEDtoflickerblue. • Firmware upgrade: RGB LED to alternate between red and green. S P E C I F I C A T I O N S Power Amplifier Power output into 8 Ohm: 75 WRMS, Both Channels Driven THD+N <0.1% Power output into 4 Ohm: 150 WRMS Single Channel Driven THD+N<0.1% THD+N: <0.01% (1 kHz, 2 channels, 1 W @ 8 Ohms) AmplifierType:ClassAB...
Page 13
Digital Coax Input: up to 24 bit/192 kHz Digital Optical Input: up to 24 bit / 96 kHz Format Support: PCM Sampling Rate: up to 192 kHz/24 bit THD+N: 0.001% (1 kHz, 2 Vrms at Pre-Out) Signal to Noise Ratio: 106 dB (A-Wtg) BluOS (Streaming Amp ONLY) Audio Formats: MP3, AAC, WMA, OGG, WMA-L, ALAC, OPUS Hi-Resolution Audio Formats: MQA, FLAC, WAV, AIFF, Supports converted DSD...
Page 14
Roksan 24 Brook Road, Designed and built Rayleigh, Essex in Great Britain. SS67XJ,UK Roksan.com +44 (0)1268 798900 Info@roksan.com info@roksan.com roksan.com Version 1. 2020...