Advertisement
Quick Links
Pitching & Striking Instructions for :-
AIRTEK KAMPER PRO 4
AIRTEK TOURER 4
Visit our YouTube Channel for an instructional video of this model
PLEASE ENSURE YOU READ THE INSTRUCTIONS THOROUGHLY
PRIOR TO ASSEMBLING YOUR NEW PURCHASE
(ANY DAMAGE THAT OCCURS AS RESULT OF FAILURE TO READ INSTRUCTIONS IS NOT COVERED BY THE WARRANTY)
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Khyam AIRTEK KAMPER PRO 4
Summary of Contents for Khyam AIRTEK KAMPER PRO 4
- Page 1 Pitching & Striking Instructions for :- AIRTEK KAMPER PRO 4 AIRTEK TOURER 4 Visit our YouTube Channel for an instructional video of this model PLEASE ENSURE YOU READ THE INSTRUCTIONS THOROUGHLY PRIOR TO ASSEMBLING YOUR NEW PURCHASE (ANY DAMAGE THAT OCCURS AS RESULT OF FAILURE TO READ INSTRUCTIONS IS NOT COVERED BY THE WARRANTY)
-
Page 2: Component Checklist
Component Checklist Prior to assembling your new purchase please carefully check the contents to make sure you are not missing any parts. Airtek Kamper Pro 4 Carry Bag Awning Porch Groundsheet Pump & hose assembly (rolled up in centre) Pegs/Peg bag... - Page 3 Pitching your tent/awning Unroll the tent/awning and peg the four corners - we recommend the use of a SPS Footprint to keep the bottom of the tent/awning clean. - Pegging points may need adjusting/tightening once the tent/awning is erected. Prior to inflating the tent/awning, unzip a couple of doorways, this allows air to enter the inside whilst inflating and prevents the unit acting like a vacuum, making the erection process easier.
- Page 4 Pitching your tent/awning Once all tubes are inflated lift the front of the unit and the frame should pop into place, it may be necessary to push the tubes into position from inside the tent/awning. Peg out the front and rear Storm Straps - Aim to peg these at least 1.5m away from unit - Further the better. Zip any open doorways shut, Adjust the corner pegging points if needed to ensure the unit is square and has sufficient tension.
- Page 5 Packing your tent/awning Unpeg all pegging points and tie guy ropes up to prevent tangling - Leave just the corners and Storm Straps pegged. (Airtek Tourer 4 - Remove Side Door Canopy Pole) To deflate the tent/awning unscrew the dust cap on the valve and depress the spring button on the valve, repeat this on all the air tubes and the tent/awning will then drop to the floor - open a couple of doorways and this will allow air to escape from inside quickly.
- Page 6 Packing your tent/awning Start Rolling the tent/awning up towards the side with the Speed Valves - This will push any remaining air in the tubes out as you roll. Squeeze as much air out as you can while you roll. Secure the rolled tent/awning with a tie, place the bag on upside down and the roll over in the carry bag (saves having to lift awning into carry bag) Zip Carry bag up and secure webbing straps on bag.
- Page 7 Q. How long are products covered for? We go that bit further at Khyam. We don’t just guarantee our products for a set time frame. We like to be more flexible because the lifespan of our products varies depending on a few factors. For example, a heavily used or poorly maintained item will probab ly have a shorter life than an averagely used or well-looked after item.
- Page 8 Q . Are Khyam awnings water resistant? All Khyam flysheet fabrics are coated to withstand in excess of 5000mm head of water in the hydrostatic head test. This is a measure by which we can test the resistance of water penetration. This is the measurement when the fabric is new and in use over a period of time this level will drop.
- Page 9 OTHER USEFUL POINTS TO BEAR IN MIND. 1. Never remove pegs by pulling up on the poles or fabric by doing this you may damage the pole or awning invalidating the guarantee. Always use a peg puller or another peg 2.
Need help?
Do you have a question about the AIRTEK KAMPER PRO 4 and is the answer not in the manual?
Questions and answers