Advertisement
1SFC380023
General
AF-Contactors are fitted with an electronic coil interface. For a given coil, this interface allows the contactor to accept a very wide voltage range. The contactor can
also be controlled by separate logic control signals from for instance a PLC. Selection of control method is done with switch S1. Control by switching voltage on A1
and A2 requires the switch in position B while control with logic signals requires the switch in position A. Use of logic control signals also requires a steady supply voltage
on A1 and A2 within the rated voltage range.
Control by switching voltage on A1 and A2 (switch S1 in position B default factory setting)
Operation of AF-contactors can be done as with conventional contactors by applying and removing voltage on A1 and A2.
Control with logic control signals (switch S1 in position A)
Use of the logic control signals also requires a steady voltage on terminals A1 and A2 within the operational limits. Minimum pulse lenght for opening and closing: 7 ms.
EN
The function of the logic control signals will no longer be guaranteed when the logic on A1 and A2 is removed. The logic control signals operates with 24 V DC and
consist of two control signals (ON and OFF_N) and a common reference (COM). To close the contactor it is enough with a control pulse at ON and to open it a removal
of voltage from OFF_N.
+24 V
Start
Stop
OV
Note: Emergency stop should disconnect A1 and A2
When used with switches the wiring can be done
according to diagram above.
ON OFF_N COM
X5
1
The functions are descibed with following diagram. "1" means 24 V DC between the control signal and COM. "0" means no voltage between the control signal and
COM.The funktion is made so that ON and OFF_N can be connected in parallel for a common ON/OFF signal. In addition to these signals the funktion limits for the
supply voltage are still valid (closing at 85% and opening at 55%), which is indecated in the diagram by high and low voltage
Noti ce.
This product has been designed for environment A. Use of this product in environment B may cause unwanted electromagnetic disturbances
in which case the user may be required to take adequate mitigation measures.
According to UL 508
Use wire Cu 75 °C only.
AF(S) 400, 460: Enclosure with min. 36 by 30 by 12 inches shuld be used.
AF(S) 580, 750: Enclosure with min. 48 by 36 by 16 inches should be used and secured by at least three latches.
AF1250: Enclosure with min. 2000 x 1000 x 600 mm should be used.
UL Short Circuit Data
Suitable for use on a circuit capable of delivering not more than the max. symmetrical amperes at the max. voltage shown on the tables below.
AF(S)400
Circuit
Fuse/Class
Breaker
A
A
600
700/L
600
600/J
1000/L
Additional Ratings
Capacitor Switching
After a short circuit, ensure that the quarter turn screws are in the correct position.
Supply voltage
+24 V
A1
A2
Contactor
Start
X5
ON
1
Stop
OFF_N
2
0V
COM
3
Relay
95
96
Note: Emergency stop should disconnect A1 and A2
When used with transistor outputs the wiring can be done
according to diagram above.
Wire dimensions for PLC interface.
3 x 0.2...2 mm²
3 x AWG 22 ... 14
X 5
O N
1
0.3 Nm
O N
2
2.6 lb.in
O F
F _
3
N
C O
M
S 1
A
P L
B
C
P L
C
ø 3.5 mm
(0.14 in)
PLC
PLC
S1
2
3
A
B
AF(S)460
Short Circiut
Voltage
Circuit
Current
Maximum
Breaker
kA
V
A
84
480
800
84
480
42
600
800
82
600
30
600
AF(S)400
AF(S)460
208V, 119 kvar, 330 FLA
208V, 142 kvar, 396 FLA
240V, 137 kvar, 330 FLA
240V, 164 kvar, 396 FLA
480V, 274 kvar, 330 FLA
480V, 329 kvar, 396 FLA
600V, 343 kvar, 330 FLA
600V, 410 kvar, 396 FLA
Supply voltage
A1
Contactor
X5
ON
1
OFF_N
2
COM
3
Relay
95
96
Wire strip length
5-6 mm
(0.2-0.24 in)
X 5
1
O N
2
O F
Supply voltage
3
F _
N
C O
on A1 and A2
S 1
M
A
P L
B
C
Position
P L
C
Fuse/Class
Short Circiut
Voltage
Current
Maximum
A
kA
V
84
480
800/L
84
480
42
600
600/J
82
600
1000/L
30
600
AF(S)580
208V, 178 kvar, 495 FLA
240V, 205 kvar, 495 FLA
480V, 411 kvar, 495 FLA
600V, 514 kvar, 495 FLA
Position
A2
Contactor
closed
Contactor
open
Low
Operationalrange
85% of lower voltage range level
55% of lower voltage range level
24V DC Signals:
Status "1" : U=15...33V DC
I =10mA at 24V
Status "0" : U=0...5V DC
1
ON
0
1
OFF_N
0
1
0
Closed
Open
AF(S)580, AF(S)750
Circuit
Fuse/Class
Short Circiut
Breaker
Current
A
A
kA
800
89
1200
42
1200/L
82
800
42
1200/L
82
AF(S)750
208V, 214 kvar, 595 FLA
240V, 247 kvar, 595 FLA
480V, 494 kvar, 595 FLA
600V, 618 kvar, 595 FLA
5/13
Control
voltage
High
Normal range
Voltage
Maximum
V
480
480
480
600
600
Advertisement
