Page 1
Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
Page 2
Wells’ discretion have the parts replaced or codes, including incorrect gas or electrical connection. Wells is not liable repaired by Wells or a Wells-authorized service agency.
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
FEATURES & OPERATING CONTROLS A. THERMOSTAT INDICATOR LIGHT On THERMOSTATICALLY CONTROLLED heated tanks, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. The desired temperature is controlled by rotating the TEMPERATURE TEMPERATURE CONTROL KNOB.
Do not operate this appliance if the control panel is damaged. Call these instructions are not your Authorized Wells Service Agent for service. followed. The technical content of this manual, including any wiring diagrams, schematics, parts breakdown illustrations and/or adjustment procedures, is intended for use by qualified technical personnel.
INSTALLATION NOTE: DO NOT discard UNPACKING & INSPECTION the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
Page 7
INSTALLATION 3. For “top-mounted” installation: a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter. c.
OPERATION CAUTION: A. WET OPERATION HOT SURFACE Make sure the drain valve is fully closed before turning thermostat ON. Exposed surfaces can be hot Add approximately 1” of hot tap water before turning the warmer ON. to the touch and may cause Use of hot water will allow a faster preheat.
Never use metal implements, wire brushes, abrasive scratch pads or steel wool to clean stainless steel. Warmer pans, insets and other vessels are subject to a harsher environment. Wells Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer pans.
Contact your Authorized Wells Service Agency to inspect warmer if water or grease contamination is suspected. Add proper amount of warm water. Turn control knob ON and...
Page 11
CLEANING INSTRUCTIONS WEEKLY CLEANING INSTRUCTIONS PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet CAUTION: operation. CHEMICAL BURN HAZARD FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. Deilimng chemicals may be caustic.
Too much water Remove water from pan until 1” of water remains in tank There are no user-serviceable components in this appliance. In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs.
EXPLODED VIEW & PARTS LIST HT227 HT200 Model: HT200, HT227 Built-in Bain Marine Style Heated Tanks IL1734 Rev. B 11/18/15 PL021A...
Page 15
EXPLODED VIEW & PARTS LIST HT200 & HT227 Built-in Baine Marine Style Heated Tanks Fig No Part No Description P2-31869 SCREEN DRAIN ASSY WARMER P2-301893 ADAPTER BAR HT200-500 DD-302884 ADAPTER BAR HT327/437 AF P2-301761 SHROUD REAR HT-200 ROHS P2-303359 SHROUD SIDE MODS ROHS...
Page 16
EXPLODED VIEW & PARTS LIST HT-327 HT-300 Model: HT300, HT327 Built-in Bain Marine Style Heated Tanks IL1735 Rev. B 11/18/15 PL021A...
Page 17
EXPLODED VIEW & PARTS LIST HT300 & HT327 Built-in Baine Marine Style Heated Tanks Fig No Part No Description P2-31869 SCREEN DRAIN ASSY WARMER P2-301893 ADAPTER BAR HT200-500 DD-302884 ADAPTER BAR HT327/437 AF P2-304105 SHROUD FRONT REAR HT-300 P2-303359 SHROUD SIDE MODS ROHS P2-302882...
Page 18
EXPLODED VIEW & PARTS LIST HT-427 HT-400 Model: HT400, HT427 Built-in Bain Marine Style Heated Tanks IL1736 Rev. B 11/20/15 PL021A...
Page 19
EXPLODED VIEW & PARTS LIST HT400 & HT427 Built-in Baine Marine Style Heated Tanks Fig No Part No Description P2-31869 SCREEN DRAIN ASSY WARMER P2-301893 ADAPTER BAR HT200-500 DD-302884 ADAPTER BAR HT327/437 AF P2-304106 SHROUD FR/RR HT400/427 P2-303359 SHROUD SIDE MODS ROHS P2-302882...
Page 20
EXPLODED VIEW & PARTS LIST HT-500 Model: HT500 Built-in Bain Marine Style Heated Tanks IL1737 Rev. B 11/20/15 PL021A...
Page 21
EXPLODED VIEW & PARTS LIST HT500 Built-in Baine Marine Style Heated Tanks Fig No Part No Description P2-31869 SCREEN DRAIN ASSY WARMER P2-301893 ADAPTER BAR HT200-500 P2-304107 SHROUD FRONT / REAR P2-303359 SHROUD SIDE MODS ROHS 2C-30397 CLIP ELEM M P 2N-46660UL...
Page 22
EXPLODED VIEW & PARTS LIST HT-527 Model: HT527 Built-in Bain Marine Style Heated Tanks IL1738 Rev. B 11/20/15 PL021A...
Page 23
EXPLODED VIEW & PARTS LIST HT527 Built-in Baine Marine Style Heated Tanks Fig No Part No Description P2-31869 SCREEN DRAIN ASSY WARMER DD-302884 ADAPTER BAR P2-304107 SHROUD FRONT / REAR P2-302882 SHROUD SIDE MODS ROHS 2C-30397 CLIP ELEM M P 2N-300706UL ELEM 240V 1650W 12 X 27"...
WS-20385 service, or to order factory authorized replacement parts, DRAIN SCREEN P2-31869 contact your Wells authorized service agency, or call: Wellslok Extension Kits for UL Listed units approved for installation in wood counter tops Wells Manufacturing 265 Hobson Street OPTIONAL 72”...