Panasonic LH2H Manual page 11

Specifications
Item
Rated operating voltage
Rated power consumption
Rated control output
Time counting direction
Measurement time range
Start input
Reset input
Rating
Input signal
Operation mode
Display method
Power failure emory
Operating time fluctuation
Voltage error
Time
accuracy
Temperature error
Setting error
Contact arrangement
Electrical life (contact)
Allowable operating voltage range
Electrical Break down voltage (Initial value)
Insulation resistance (Initial value)
Functional vibration resistance
Destructive vibration resistance
Mechanical
Functional shock resistance
Destructive shock resistance
Operation temperature
Operating
Storage temperature
conditions
Ambient humidity
Protective construction
* The factory default preset value is set to 0.1.
Applicable standard
(EMI)EN61000-6-4
Radiation interference electric field strength
Noise terminal voltage
(EMS)EN61000-6-2
Static discharge immunity
EMC
RF electromagnetic field immunity
EFT/B immunity
Conductivity noise immunity
Power frequency magnetic field immunity
Addition or Subtraction (selectable by front switch)
0 to 999999.9h/0 to 3999d23.9h (selectable by slide switch on side)
0 to 999h59m59s/0 to 9999h59.9m (selectable by slide switch on side)
Min. input signal width: Min. 30 ms
Min. input signal width: Min. 30 ms
• Non-voltage input using contacts or open-collector connection
• Input impedance; when shorted: Max. 1 kΩ, when open: Min. 100 kΩ
• Residual voltage: Max. 2 V
Totalizing ON delay, Signal ON delay, Signal flicker, Pulse ON delay
(selectable by front switch)
(Switch between red and green for backlight, and between lit and flashing for time up.)
EEP-ROM (Overwriting times: 10
±0.01% ±50 ms
in case of power on start
±0.01% ±30 ms
in case of input signal start
1 Form A (Open collector)
10 7 operations (at rated control voltage)
85 to 110% of rated operating voltage
Between input and output: 1,500 V AC, for 1 min.
Between input and output: 100 MΩ (at 500 V DC)
10 to 55 Hz (1 cycle/min), Single amplitude: 0.15 mm (10 min. on 3 axes)
10 to 55 Hz (1 cycle/min), Single amplitude: 0.375 mm (1 hr. on 3 axes)
Min. 98 m/s
Min. 294 m/s
–10 to 55°C
–25 to +65°C
35 to 85% RH (non-condensing)
IP66 (front panel with mounting bracket and rubber gasket)
EN55011 Group1 ClassA
EN55011 Group1 ClassA
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-6
EN61000-4-8
Descriptions
24 V DC
Max. 1.5 W
100 mA 30 V DC
7-segment LCD
operations or more)
5
 Rated operating voltage:

85 to 110%

Ambient temperature:

–10 to +55°C
2 (4 times on 3 axes)
(5 times on 3 axes)
2
+14 to +131°F (without frost or dew)
–13 to +149°F (without frost or dew)
4 kV contact
8 kV air
10 V/m AM modulation (80 MHz to 1 GHz)
10 V/m pulse modulation (895 MHz to 905 MHz)
2 kV (power supply line)
1 kV (signal line)
10 V/m AM modulation (0.15 MHz to 80 MHz)
30 A/m (50 Hz)
LH2H




+14 to +131°F
157