These factors must be supplied by the person(s) caring for and operating this equipment. ONLY YOU CAN PREVENT ACCIDENTS!! O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 3 -...
Model 810 has a huge 10” x 18” chipper inlet opening and a 21” diameter feed roll. This, coupled with the largest infeed hopper in the industry, 1,881 square inches, allows our machine to ingest whole trees, branches and all.
It has been and will continue to be the policy of SALSCO to update existing machines at its own discretion. Whenever possible, new designs will be made in such a way that they can be "Retro Fit" if so desired.
ARE THE AMERICAN NATIONAL STANDARD OF POWERED SHREDDERS/GRINDERS SAFETY SPECIFICATIONS, PROVIDED BY ANSI AND THE O.P.E.I. THE FOLLOWING COUTIONS ARE PROVIDED BY SALSCO AS A QUICK REFERENCE ONLY AND ARE NOT MEANT TO REPLACE THE PRECAUTIONS ON THE FOLLOWING PAGES.
Page 7
BRUSH CHIPPERS ANSI Z133.1-2006 American National Standard for Arboricultural Operations Safety Requirements O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 7 -...
Page 8
BRUSH REMOVAL CHIPPING ANSI Z133.1-2006 American National Standard for Arboricultural Operations Safety Requirements O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 8 -...
Page 9
SAFETY DECALS PART # 0314020 PART # 0314062 PART # 0314049 PART # 0314029 O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 9 -...
Page 10
SAFETY DECALS PART # 0314060 PART # 0314062 PART # 0314015 PART # 0314063 O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 10 -...
Page 11
4. COUNT YOUR EXTREMITIES AGAIN. BE SURE THIS NUMBER MATCHES YOUR STARTING NUMBER. WHILE PERFORMING MAINTENANCE OR REPAIR, ALWAYS REMOVE KEY FROM ENGINE! O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 11 -...
Should you drop a nut, bolt or blade in the housing you must retrieve it before you start up the machine. HINT: Salsco recommends replacement of nuts when replacing or sharpening chipper blades. The locking ability of these nuts may have been violated.
Page 13
Once machine has come to a halt, re-grease bearings. Send machine to work. It’s ready! REMEMBER: REMOVE KEY FROM ENGINE, DISCONNECT BATTERY CABLES AND LOCK-OUT UNIT WHENEVER PERFORMING SERVICE AND MAINTENANCE. O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 13 -...
Now press both buttons to say “OK”. Keep pressing both buttons until you get back to the zero with a dot. O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 22 -...
Page 23
Change the Lo to be 100 less than the Hi. All the other settings are set to zero. Except machines with auto reverse on these machines set the back to .250. O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 23 -...
Below is a quick reference chart for various “Flat Head Cap Screws” and the torque recommendations. VALUES ARE STATED IN FOOT POUNDS BOLT SIZE Thds Per Inch SAE Grade 5 SAE Grade 8 ¼ 5/16 7/16 ½ 9/16 ¾ O:\Manuals\810 CHIPPER\810 WOOD..BRUSH CHIPPER P.W. 10.30.2017.doc - 27 -...
Your Salsco Commercial or Turf Equipment product is a commercial type product and is normally manufactured and sold for commercial or industrial use. Salsco will, for the original purchaser, for one (1) year from the date of purchase (90 days if used for rental purposes) repair or replace, free of charge, any SALSCO part or parts found to be defective in material, workmanship or both.