Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ubiquiti UniFi ULED-AC
Summary of Contents for Ubiquiti UniFi ULED-AC
- Page 1 Network-Managed LED Panel Powered by AC Model: ULED-AC...
-
Page 2: Package Contents
• Web browser: Google Chrome (Other browsers may have limited functionality.) • UniFi Dimmer Switch, model UDIM-AC or UDIM-AT TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable ™... -
Page 3: Installation Requirements
Installation Requirements • Phillips screwdriver • Wire stripper/cutter • Needle-nose pliers (Optional) IMPORTANT: The ULED-AC is to be installed by a qualified electrician in accordance with local electrical codes and regulations. IMPORTANT : Le ULED-AC doit être installé par un électricien qualifié conformément aux codes électriques locaux et des règlements. -
Page 4: Network Topology Requirements
Network Topology Requirements Network topology requirements are as follows: • DHCP-enabled network (for the UniFi LED Panel to obtain an IP address) • Network switch (for wired configuration), or access point (for wireless configuration) • For UniFi Dimmer Switch only: A UniFi Dimmer Switch connected to the same Layer 2 network as the UniFi LED Panel •... - Page 5 100-277VAC UAP-AC-PRO ULED-AC 100-240VAC 802.3af PoE UniFi LED UDIM-AT UDIM-AC UniFi PoE Switch UniFi EoT Controller UniFi Application Server USG-XG-8 (DHCP Server) Internet Sample Network Diagram - Wireless Topology...
- Page 6 ULED-AC Ethernet 100-277VAC UAP-AC-PRO 802.3af PoE UDIM-AT UniFi LED UniFi EoT UniFi PoE Switch Controller UniFi Application Server USG-XG-8 (DHCP Server) Internet Sample Network Diagram - Wired Topology *640-00340-03* 640-00340-03...
-
Page 7: Daisy-Chain Configuration
Daisy-Chain Configuration For installations using multiple UniFi LED Panels in a wired configuration, we recommend using a daisy chain topology, as illustrated in the following diagram. (Additional LED Panels) 100-277VAC Ethernet ULED-AC 100-277VAC Ethernet ULED-AC 802.3af PoE UDIM-AT UniFi PoE Switch UniFi EoT Controller UniFi Application Server... -
Page 8: Hardware Overview
Hardware Overview Status LED State Status Flashing White Initializing. Steady White System ready. Steady Blue Adopted by EoT Controller. Alternating Firmware upgrade is taking place. White/Blue Ports Ethernet Ethernet Use these 10/100 Ethernet ports to connect to the LAN or to daisy-chain with other UniFi LED Panels. -
Page 9: Terminal Block
Button Reset Reset The Reset button serves two functions: • Restart Press and release the Reset button quickly. • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. Terminal Block Connections for AC power: N (Neutral), L (Live), and (Earth ground). -
Page 10: Installation
Installation To install and configure the UniFi LED Panel: 1. Lift the panel and seat it in an opening in the ceiling grid. 2. If the panel will use Wi-Fi to connect to the network, go to step 3. If the panel will use a wired connection to the network, connect an Ethernet cable to the Main port. - Page 11 4. Remove a knockout from the Junction Box and feed the power cable through the knockout into the Junction Box. 5. Connect each of the cable’s wires to the appropriate Terminal Block connector as follows: • Connect the Neutral (white) wire to N. •...
- Page 12 Daisy Chain Configuration (Optional) For each additional panel in the chain: 1. Make the following changes to the UniFi LED Panel which is currently the last panel in the chain: a. If the new panel will use a wired connection to the network, connect an Ethernet cable to the Secondary port of the current last UniFi LED Panel.
- Page 13 Configuring the UniFi LED Panel Follow the instructions for the software you wish to use: UniFi LED App 1. Install the UniFi LED app on your smartphone or mobile device. The app is available from the App Store® or Google Play Store.
- Page 14 Layer 2 network as the UniFi LED Panel: • Ubuntu users Download the software from: https://github.com/ubiquiti/eot-controller • UAS users Install the software using the UniFi Application Server (UAS) management console. 2. Launch a web browser and go to: http://localhost:20080 3.
-
Page 15: Specifications
Specifications ULED-AC Dimensions 602 x 602 x 56.7 mm (23.7 x 23.7 x 2.23") Weight 5.3 kg (11.68 lb) Networking Interface 802.11 b/g/n (2.4 GHz Only) 10/100 Ethernet Port Wireless Security WEP, WPA/WPA2 Personal Connectivity Wi-Fi 802.11 b/g/n, Bluetooth LE 4.1 Buttons Reset LEDs... -
Page 16: Safety Notices
UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above... -
Page 17: Warranty Conditions
Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation;... -
Page 18: Limitation Of Liability
FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer’s selection of products... - Page 19 Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
-
Page 20: Rf Exposure Warning
RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilisées pour ce transmetteur doivent être installé... - Page 21 Deutsch Die Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu...
-
Page 22: Declaration Of Conformity
на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa ULED-AC u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.ubnt.com/compliance Čeština [Czech]... - Page 23 Íslenska [Icelandic] Hér með lýsir UBIQUITI NETWORKS yfir því að ULED-AC er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance...
- Page 24 . u b n t . c o m ©2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, TOUGHCable, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc.