Summary of Contents for Atlas Copco Cobra PROe
- Page 1 COBRA Safety and operating instructions Petrol breakers © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions...
-
Page 3: Table Of Contents
Every month ............................18 Gearbox oil level check ........................18 Service ..............................18 Repair ............................... 18 Replacing the starter cord ........................18 Troubleshooting ............................19 Storage ................................19 Disposal ................................ 20 © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... - Page 4 Machine data ............................22 Noise and vibration declaration statement ..................23 Noise and vibration data ........................23 EC Declaration of Conformity ........................24 EU Declaration of Conformity ........................ 24 © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions...
-
Page 5: Introduction
Save all warnings and instructions for future reference. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 6: Installation, Precautions
Make sure that there are no undetected ► weight. sources of gas or explosives. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... - Page 7 Control dusts and fumes at the source where possible. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions...
- Page 8 When the percussion mechanism is activated, ► the only body contact with the machine you © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions...
- Page 9 Check the composition of the material before ► operating. Watch out for concealed cables and pipes for ► example electricity, telephone, water, gas and sewage lines etc. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions...
-
Page 10: Maintenance, Precautions
Touching it can lead to burns and cuts. Never touch a hot or sharp working tool. ► Wait until the working tool has cooled down ► before carrying out maintenance work. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 11: Overview
D. The CE symbol means that the machine is EC- A. Fuel filler cap approved. See the EC Declaration of B. Carburettor © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 12: Noise Level Label
Atlas Copco representative for advice on performing any such task. the correct two-stroke oil. Operate with chisel retainer in place. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 13: Mixing The Petrol And Oil
Filling procedure 1. Stop the engine and let it cool down before filling the tank. 2. The machine must be in an upright position when filling it with fuel. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 14: Working Tool
Check the length (B), that it is according to the • Wide bladed chisel ordered machine type. The wide bladed chisel is used in soft materials, such as asphalt and frozen ground. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 15: Operation
1. Remove the fuel cap and check the fuel level. ◆ The feed force must be adjusted so that the Secure the fuel cap before start. handle is pressed 'half way down'. This position © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... - Page 16 ◆ Operate for 2-3 seconds at one point before moving to another operating point. Operating © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions...
-
Page 17: When Taking A Break
Check for damaged or loose wiring. If found, the oil level in the impact unit should be checked contact an authorised workshop. every day. The machine must be upright when © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 18: Every Month
Place the knot on the starter spring in the recess on the inside of the pulley and wind in 6 months of continuous use • the starter spring (anti-clockwise). 12 months of continuous use • © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 19: Troubleshooting
If the machine still does not function satisfactorily, contact an authorised workshop. Storage ◆ Empty the tank before storing the machine. ◆ Check that the machine is properly cleaned before putting it away for storage. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 20: Disposal
Before a petrol driven machine is deposited it must be emptied and cleaned of all oil and petrol. Remaining oil and petrol must be dealt with in a way that does not affect the environment. © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 21: Technical Data
40 J at 1620 bpm Lubrication Impact mechanism through separate oil bath Oil type for impact unit Atlas Copco IMPACT-OIL Oil capacity, litres (oz) 0.1 (3.38) Oil consumption, litres/hour (oz/hour) 0.005 (0.17) © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 22: Machine Data
Spark plug (recommended) Champion RCJ8 Spark plug gap, mm (in.) 0.6–0.7 (0.024–0.028) 0.6–0.7 (0.024–0.028) Ambient temperature °C (°F) -15 to +37 (5 to 98.6) -15 to +37 (5 to 98.6) © Atlas Copco Airpower | 9800 1629 01 | 2018-01-01 Original instructions... -
Page 23: Noise And Vibration Declaration Statement
We, Atlas Copco Airpower, cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. -
Page 24: Ec Declaration Of Conformity
Safety and operating instructions COBRA TTe EC Declaration of Conformity EU Declaration of Conformity We, Atlas Copco Airpower n.v., declare under our sole responsibility, that the product Machine name Motor Breaker Machine type Serial number Which falls under the provisions of article 12.2 of the EC Directive 2006/42/EC on the approximation of the laws of the Member States relating to machinery, is in conformity with the relevant Essential Health and Safety Requirements of this directive. - Page 28 Any unauthorized use or copying of the contents or any part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers, and drawings. www.atlascopco.com...