Page 1
SERVICE MANUAL CTM5140 51CM CTV Effective: JULY02 CTM5140SERV...
Page 2
Ver1.2 1 December 2001
B+ adjustment VCO & AFT NICAM Electrical RF AGC Alignment Adjustment properties adjustment checking for chassis Sub-brightness White balance Aging Adjustment of Sub-color & Adjustment Adjustment screen voltage Sub-tint and focus adjustment Pincushion and Screen center Screen center QC checking screen width...
Page 3
Ver1.2 1 December 2001 Press “4” to enter sharpness setting menu,
( 50% sharpness in 3.58 system (TV) ( 50% sharpness in 3.58 system (AV) + 50% sharpness in 4.43 system (TV) + 50% sharpness in 4.43 system (AV) , Maximum sharpness...
Page 4
Ver1.2 1 December 2001 Press “0” to enter OSD setting menu,
OSD Horizontal position of OSD TXCX OSD intensity when maximum contrast RGCN OSD intensity when minimum contrast TNTX Maximum tint level TNTN Minimum tint level
1.
Page 5
Ver1.2 1 December 2001
#$%&
'#$% #$%&
#() * 1. Enter D-mode, and connect the probe of Oscilloscope to the conjunction between R217 and P201 (B-out). 2. Apply the Grey-scale/Colour-bar (NTSC signal) to the AV input, in STANDARD status. 3. Select CNTC to adjust the sub-contrast, until that the amplitude “A” is 2.5V as shown below.
Page 6
Ver1.2 1 December 2001 -
( & "
() 1. Apply the crosshatch pattern (PAL signal) to the RF input, in STANDARD status. 2. Select HPOS50 to adjust the Horizontal center. 3. Select VPOS50 to adjust the Vertical center. 4. Select HIGH50 to adjust the Vertical amplitude. 5.
Page 7
Ver1.2 1 December 2001
VCDM0 (default value: 68) BIT Item System switch: 0 : normal identify mode 1 : weak signal identify mode White peak suppress: 0: on 1: off ABL gain 00: -0.74v 01: -0.64v 10: -0.37v 11: -0.12v ABL start point 00: -0.01v 01: -0.11v 10: -0.3v 11: -0.45v CW-SW: TB1238N, pin 29 Fsc CW output 0 : AUTO, 1 : 4.43M...
Page 8
Ver1.2 1 December 2001 MODE1 BIT Item Logo: 0: disable 1: TCL Logo No. of channel: 0: 49 1: 99 No use Menu background 0: disable 1: black background No. of AV 0: 1 1: 2 SECAM 0: off 1: on D-mode 0: enable 1: disable No use...
Page 13
PART NUMBER DESCRIPTION LOCATION 46-20598W-04X PIN BASE *4 TJC1-4A P401, FOR DY CONNECTOR 46-33079W-02X PIN BASE *2 TJC3-2A P602, FOR FRONT CAB. (SPK) 46-33079W-02X PIN BASE *2 TJC3-2A P001, FOR AGING TEST 46-33079W-04X PIN BASE *4 TJC3-4A P402, FOR CRT BD P502 46-33079W-05X PIN BASE *5 TJC3-5A P201, FOR CRT BD P503...
Page 14
PART NUMBER DESCRIPTION LOCATION 18-KE0475-JNX RES. H. VOLT. CC 4.7M OHM 1/2W R805, R835, R835A 20-TR502H-5CX TRIMMER B5K HORIZ TYPE VR801 22-PTC360-XX0 PTC 36 OHM RT801 25-343260-M1X CAP. ELEC 2200UF 25V 20% 12X25 C845 25-BDA471-M1X CAP. ELEC 470 UF 25V +/-20% C842 25-BDB470-M1X CAP.
Page 15
PART NUMBER DESCRIPTION LOCATION 40-2111MU-RMA P.C.B. IR HANDSET BD 45-COS455-KY0 CER RESONATOR 455 KHZ X1501 49-HS46F0-00X RUBBER PAD KEYS 55-HS46FB-0HA CASE LOWER - REMOTE HANDSET 55-HS46FD-0HA DOOR BATT. - REMOTE HANDSET 55-HS46FT-0HA CASE UPPER - REMOTE HANDSET 58-HS46F0-YUI INLAY IR TRANSMITTER BD 63-B26060-BT2 S/T SCREW B 2.6 X 6 BT 67-26968X-0E2...