Advertisement
Alignment
CTCSS TX Deviation
1. Tune the frequency to 440.050 MHz, then activate the
CTCSS encoder with a "100 Hz" tone, and set the trans-
mit power level to "LOW."
2. Press the [ F/W ] key, then press the [ BAND ( BAND DN )]
key to set the alignment parameter to "A5 CTC.xxx
3. With in five second of appearing the "A5 CTC.xxx
the display, press the PTT switch to activate the trans-
mitter (with no microphone input), adjust the DIAL
knob so that the deviation meter reading is 0.7 kHz
(±0.05 kHz).
4. Tune the frequency to 146.050 MHz, then activate the
CTCSS encoder with a "100 Hz" tone, and set the trans-
mit power level to "LOW."
5. Press the [ F/W ] key to recall the alignment parameter
A5 CTC.xxx
A5 CTC.xxx."
A5 CTC.xxx
to "A5 CTC.xxx
A5 CTC.xxx
6. With in five second of appearing the "A5 CTC.xxx
the display, press the PTT switch to activate the trans-
mitter (with no microphone input), adjust the DIAL
knob so that the deviation meter reading is 0.7 kHz
(±0.05 kHz).
S-meter Sensitivity
1. Tune the frequency to 440.050 MHz.
2. Inject a 440.050 MHz signal at a level of –5 dBμV (with
1 kHz modulation @±3.5 kHz deviation) from the RF
signal generator.
3. Press the [ F/W ] key, then press the [ BAND ( BAND DN )]
key to set the alignment parameter to "A6 SM U
4. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
5. Increase the RF signal generator output level to +23
dBμV.
6. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
7. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
8. Tune the frequency to 850.050 MHz.
9. Inject a 850.050 MHz signal at a level of +5 dBμV (with
1 kHz modulation @±3.5 kHz deviation) from the RF
signal generator.
10. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
11. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
12. Increase the RF signal generator output level to +31
dBμV.
13. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
14. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
12
15. Tune the frequency to 146.050 MHz.
16. Inject a 146.050 MHz signal at a level of –5 dBμV (with
1 kHz modulation @±3.5 kHz deviation) from the RF
signal generator.
17. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
A5 CTC.xxx
A5 CTC.xxx."
A5 CTC.xxx
A5 CTC.xxx
18. With in five second of appearing the "A6 SM U
A5 CTC.xxx
A5 CTC.xxx" on
A5 CTC.xxx
A5 CTC.xxx
the display, press the [ ( MHz )] key.
19. Increase the RF signal generator output level to +23
dBμV.
20. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
21. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
22. Tune the frequency to 230.050 MHz.
23. Inject a 230.050 MHz signal at a level of –5 dBμV (with
1 kHz modulation @±3.5 kHz deviation) from the RF
A5 CTC.xxx
A5 CTC.xxx" on
A5 CTC.xxx
A5 CTC.xxx
signal generator.
24. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
25. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
26. Increase the RF signal generator output level to +23
dBμV.
27. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
28. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
29. Tune the frequency to 350.050 MHz.
30. Inject a 350.050 MHz signal at a level of –5 dBμV (with
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
1 kHz modulation @±3.5 kHz deviation) from the RF
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
signal generator.
31. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
32. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
33. Increase the RF signal generator output level to +23
A6 SM U
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
dBμV.
34. Press the [ F/W ] key to recall the alignment parameter
to "A6 SM U
35. With in five second of appearing the "A6 SM U
the display, press the [ ( MHz )] key.
DC Voltmeter
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D " on
1. Set the power supply voltage to 9.9 V.
2. Press the [ F/W ] key, then press the [ BAND ( BAND DN )]
key to set the alignment parameter to "A7 BAT RV
3. With in five second of appearing the "A7 BAT RV
the display, press the [ HM/RV ] key.
To close the alignment mote, just turn the power off by rotating
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
A6 SM U
the VOL knob fully counter clockwise. The next time the trans-
ceiver is turned on, normal operation may resume.
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D ."
A6 SM U
A6 SM U
A6 SM U
FT-60R/E Technical Supplement
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
A6 SM U
A6 SM U
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U/D D D D D " on
A6 SM U
A6 SM U
A6 SM U
A7 BAT RV."
A7 BAT RV
A7 BAT RV
A7 BAT RV
A7 BAT RV
A7 BAT RV
A7 BAT RV" on
A7 BAT RV
Advertisement
