Table of Contents
Advertisement
Quick Links
LAN Control Utility
User Manual
Preparation/SetUp .........................................................................2
Preparation before using the network function ...........................................2
Connection ..................................................................................................2
Installation ...................................................................................................3
Setting the IP address of the projector .......................................................5
When using a DHCP server ...........................................................................................6
When not using a DHCP server .....................................................................................7
Telnet setting ...............................................................................................8
Setting the password (Password Setup) .......................................................................9
Setting the display language of ProjectorView (language) ............................................9
Setting the LAN control (LAN-Controlled Mode) .........................................................10
PJLink™ certifi cation (PJLink certifi cation Mode) .......................................................10
Save and exit ...............................................................................................................11
ProjectorView ...............................................................................12
Using the ProjectorView ............................................................................12
How to start up ............................................................................................................12
VIRTUAL REMOTE controller .......................................................................................14
E-mail notifi cation function ..........................................................................................14
Initial setting .................................................................................................................15
Support for the PJLink™ function ...............................................16
Contents
EN-1
Advertisement
Table of Contents
Related Manuals for Mitsubishi XD1000U
Summary of Contents for Mitsubishi XD1000U
-
Page 1: Table Of Contents
LAN Control Utility User Manual Contents Preparation/SetUp .................2 Preparation before using the network function ...........2 Connection ....................2 Installation ....................3 Setting the IP address of the projector ............5 When using a DHCP server ...................6 When not using a DHCP server ..................7 Telnet setting ....................8 Setting the password (Password Setup) ...............9 Setting the display language of ProjectorView (language) ..........9... -
Page 2: Preparation/Setup
Preparation/SetUp Preparation before using the network function This projector is equipped with the network function to control and monitor the projector’s operations using a Web browser and to send e-mail notifi cation. Before using the network function, perform the following three preparation steps. (1) ... -
Page 3: Connection
Preparation/SetUp (continued) Connection Computer LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) to LAN terminal LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) to LAN terminal External HUB Use a straight-through category-5 cable for LAN connection. • Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged •... - Page 4 When the installation process is completed, click Close. How to remove Mitsubishi Projector Control Device Installer Select [Start] - [Control Panel] - [Add or Remove Programs] - [Mitsubishi Projector - Control Device Installer] and click [Remove] (in the case of Windows ®...
-
Page 5: Setting The Ip Address Of The Projector
Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the projector. Start the Projector-Control Device Installer. ・ Select [Start] - [All Programs] - [Mitsubishi] - [Mitsubishi Projector - Control Device Installer] (in the case of Windows XP). -
Page 6: When Using A Dhcp Server
Preparation/SetUp (continued) When using a DHCP server Select [Obtain an IP address automatically] and click Next. Click Next. Check that the options are marked with check- • marks as shown on the right. Keep them un- changed for normal use. Click Assign. -
Page 7: When Not Using A Dhcp Server
Preparation/SetUp (continued) When not using a DHCP server Select [Assign a specifi c IP address] and click Next. Enter a fi xed IP address (for example, 192.168.0.1) and click Next. Click Assign. Click Finish. Click the Search button. • Check the IP address you set. (Note 2) When using the error/alert e-mail notifi... -
Page 8: Telnet Setting
PJLink™ certifi cation that are necessary for the operation state control tool (commercially available) that uses the projector operation control/monitor tool ProjectorView and the industry standard PJLink™ protocol. Start the Projector-Control Device Installer. Select [Start] - [All Programs] - [Mitsubishi] - • [Mitsubishi Projector - Control Device Installer] (in the case of Windows XP). -
Page 9: Setting The Password (Password Setup)
Setting the password (Password Setup) Enter “0” and press the Enter key. Enter a new password (example: “proj2000“) and press the Enter key. (Default password is MITSUBISHI.) Setting the display language of ProjectorView (language) Enter “1” and press the Enter key. -
Page 10: Setting The Lan Control (Lan-Controlled Mode)
Preparation/SetUp (continued) Setting the LAN control (LAN-Controlled Mode) Enter “3” and press the Enter key. To enable the e-mail notifi cation function of Projector- View, enter 1 and press the Enter key. (Default is OFF (0).) (See pages 12 - 15 for ProjectorView function.) Setting the PJLink™... -
Page 11: Save And Exit
Preparation/SetUp (continued) Save and exit Enter “9” and press the Enter key. The setting screen is shaded and the setting process completes. • Because the password, display language, LAN control, and PJLink ™ certifi cation are set using the telnet function, you can also set them on the command prompt window of the personal computer. -
Page 12: Projectorview
・ State information indication (projector’s name, temperature, lamp operation time, error/alert, etc.) ・ E-mail notifi cation in case of error/alert How to start up Start the Projector-Control Device Installer. Select [Start] - [All Programs] - [Mitsubishi] - • [Mitsubishi Projector - Control Device Installer] (in the case of Windows XP). - Page 13 ProjectorView (continued) The password input screen appears. Enter the password you set. The default password is MITSUBISHI. • (Note 2) If you input a wrong password three successive times, the Web browser is closed. In this case, repeat from step 1.
-
Page 14: Virtual Remote Controller
ProjectorView (continued) VIRTUAL REMOTE controller Put a checkmark in the box of the Virtual remote enabled on the ProjectorView main screen, and click the VIRTUAL REMOTE button. The following Virtual Remote window appears. For the functional descriptions of each button, see the user manual of the projector. E-mail notifi... -
Page 15: Initial Setting
ProjectorView (continued) Initial setting To load information on the projector such as model name and lamp operating time, set the projector data in advance. Click the SETUP button on the ProjectorView main screen. The Projector Setup screen appears. Enter data according to the description of each setting item. (Note 4) You can’t change the Projector model, Serial number, Operating hours, and Lamp hours. -
Page 16: Support For The Pjlink™ Function
Setup window is returned. INF1? Inquiry about the “MITSUBISHI” is returned. manufacturer name INF2? Inquiry about the “XD2000U” or "XD1000U" is returned. model name INF0? Inquiry about other information CLSS? Inquiry about the “1” is returned. class information •... - Page 17 • The operating time and temperature may not be displayed correctly. In this case, close the browser, recognize this projector using Mitsubishi Projector Control Device Installer, and then start the browser again. (Refer to “How to start up” of ProjectorView.) •...