Lenovo ideapad 510S-13ISK Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Notebook
  5. ideapad 510S-13ISK
  6. Hardware maintenance manual

Lenovo ideapad 510S-13ISK Hardware Maintenance Manual

Hide thumbs Also See for ideapad 510S-13ISK:
Table of Contents

Advertisement

Quick Links

Download this manual
ideapad 510S-13ISK
ideapad 510S-13IKB
Hardware
Maintenance
Manual

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ideapad 510S-13ISK

Summary of Contents for Lenovo ideapad 510S-13ISK

  • Page 1 510S-13ISK ideapad 510S-13IKB Hardware Maintenance Manual...
  • Page 2 Note: • Before using this information and the product it supports, be sure to read the general information under “Notices” on page 80. First Edition (July 2016) © Copyright Lenovo 2016. All rights reserved. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. © 2016 Lenovo...

  • Page 3: Table Of Contents

    Power-on password ..........24 Hard-disk password ..........24 Administrator password ........24 Power management ........25 Screen blank state ..........25 Putting the computer to sleep or shutting it down ..............25 Putting your computer to sleep ......25 Shutting down the computer ......26 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB ..........27 Specifications ..........27 Status indicators ........... 29 Hotkeys............30 FRU replacement notices ......31 Screw notices ..........31 Removing and replacing an FRU ....32 1010 Base cover ..........33...

  • Page 4: About This Manual

    • The product-specific section includes service, reference, and product-specific parts information. Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under “Safety information” on page 1 and “Important service information” on page 16.

  • Page 5: Safety Information

    Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 • “Handling devices that are sensitive to electrostatic discharge” on page 6 • “Grounding requirements” on page 6 • “Safety notices: multilingual translations” on page 7 • “Laser compliance statement” on page 14...

  • Page 6: General Safety

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. • Do not perform any action that causes hazards to the customer, or that makes the machine unsafe.

  • Page 7: Electrical Safety

    About this manual Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges.
  • Page 8 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. • Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Caution: do not become a victim yourself.

  • Page 9: Safety Inspection Guide

    The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 8. Check for worn, frayed, or pinched cables.

  • Page 10: Handling Devices That Are Sensitive To Electrostatic Discharge

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted here.

  • Page 11: Safety Notices: Multilingual Translations

    About this manual Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds.
  • Page 12 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations.
  • Page 13 About this manual Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
  • Page 14 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations.
  • Page 15 About this manual Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à...
  • Page 16 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
  • Page 17 About this manual Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.

  • Page 18: Laser Compliance Statement

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
  • Page 19 About this manual A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.

  • Page 20: Important Service Information

    Strategy for replacing FRUs Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://support.lenovo.com. 2. Enter the serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.

  • Page 21: Strategy For Replacing A Hard Disk Drive

    Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. • Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one. • If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.

  • Page 22: Important Information About Replacing Rohs Compliant Frus

    Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.

  • Page 23: General Checkout

    General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • Carefully remove screws for reuse when replacing FRUs. • Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered.

  • Page 24: What To Do First

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customer’s name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer.

  • Page 25: Power System Checkout

    • If the computer does not charge during operation, go to “Checking operational charging”. To check the AC adapter, follow the steps below: 1. Unplug the AC adapter cable from the computer. 2. Measure the output voltage at the plug of the AC adapter cable. See the following figure: Voltage (V DC) Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the AC adapter. 4. If the voltage is acceptable, do the following: • Replace the system board. • If the problem persists, go to “Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB” on page 27. Note: Noise from the AC adapter does not always indicate a defect. Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.

  • Page 26: Checking The Battery Pack

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section. Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life. To check your battery, move your cursor to the Power Meter icon in the icon ® tray of the Windows taskbar and wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon. Note: If the battery pack becomes hot, it may not be able to be charged.

  • Page 27: Related Service Information

    System and run System Recovery. For details of OneKey Recovery System, see the User Guide for Lenovo OneKey Recovery system . Note: This will delete all the new data on the system partition (C drive), which is not recoverable. Make sure to back up your critical data before you perform this action.

  • Page 28: Passwords

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Passwords As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the administrator password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.

  • Page 29: Power Management

    Related service information Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation. Screen blank state If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing To end screen blank state and resume normal operation, press any key on the keyboard Putting the computer to sleep or shutting it down When you have finished working with your computer, you can put it to sleep or shut it down.

  • Page 30: Shutting Down The Computer

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down your computer, do one of the following: • Select the Start button, then select Power → Shut down. • Right-click or press the Start button in the lower-left corner and select Shut down or sign out → Shut down.

  • Page 31: Lenovo Ideapad 510S-13Isk/Ideapad 510S-13Ikb

    This chapter presents the following product-specific service references and product-specific parts information: • “Specifications” on page 27 • “Status indicators” on page 29 • “Hotkeys” on page 30 • “FRU replacement notices” on page 31 • “Removing and replacing an FRU” on page 32 • “Locations” on page 62 • “Parts list” on page 64 Specifications The following table lists the specifications of the Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB: Table 1. Specifications Form Factor Dimensions Appr. 320 mm × 225 mm × 18.7 mm Weight Appr. 1.5 kg LCD size 13.3-inch Processor Click Start, right-click File Explorer, and then click Properties.
  • Page 32 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Table 1. Specifications (continued) I/O Ports USB 2.0 × 1, USB 3.0 × 2 Audio Combo audio jack × 1 Video/Audio HDMI port × 1 Ethernet RJ-45 × 1 (1000 Mbps) Card reader Memory card slot (SD/SDHC/SDXC/MMC) Battery pack Type Li-ion battery pack Cells/Capacity 2 cells, 35 Wh Note: The capacity given here is the typical or average capacity as measured in a specific test environment. Capacities measured in other environments may differ but are no lower than the rated capacity (see product label). AC power adapter Input 100 - 240 V, 50 - 60 Hz AC O utput voltage 20 V DC Power...

  • Page 33: Status Indicators

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Status indicators The system status indicators below show the computer status: Table 2. Status indicators AC power Indicator status Meaning adapter status The computer is in sleep mode or turned off; The battery has more than 20% charge. Disconnected The battery has between 5% and Solid amber 20% charge. The battery has between 1% and 5% Fast blinking amber charge. The battery is being charged. When Slow blinking amber battery charge reaches 20%, the blinking color changes to white. The battery has between 20% and 80% charge and is still charging. Connected Slow blinking white When the battery reaches 80% charge the light will stop blinking. The battery has more than 80% Solid white charge, charging will continue until the battery is fully charged.

  • Page 34: Hotkeys

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Hotkeys You can access certain system settings quickly by pressing the appropriate hotkeys. Table 3. Hotkeys Enables/disables Airplane Mutes/unmutes the sound. mode. Enables/disables the Decreases the volume level. camera. Locks/unlocks the currently Increases the volume level. active window. Toggles the display Enables/disables the between the computer and microphone. an external device. Refreshes the desktop or Decreases the display the currently active window. brightness. Enables/disables the Increases the display touchpad. brightness.

  • Page 35: Fru Replacement Notices

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: • They maintain tight connections. • They do not easily come loose, even with shock or vibration. • They are harder to tighten.

  • Page 36: Removing And Replacing An Fru

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 31. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed. 4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts. 5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure.

  • Page 37: 1010 Base Cover

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1010 Base cover Figure 1. Removal steps of base cover Remove the screws 1. Step Screw (quantity) Color Torque M2.5 × 6 mm, Phillips-head, nylok-coated Black/ 1.0~1.5 kgf*cm (10) log low---log up & log low---io board--- Silver log up & log low---mb---log up & log low--- right side hinge---log up & log low---left side hinge---klock bracket---log up Remove the base cover in the directions shown by arrows 2 and 3.
  • Page 38 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: The following labels need to be peeled off from the old base cover and put on the new base cover. Rating label (66 x 24 mm) Rating label (43 x 24 mm) Indonesia rating label For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover. For the location of each label, refer to the following figures:...

  • Page 39: 1020 Battery Pack

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1020 Battery pack DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove this FRU: • “1010 Base cover” on page 33 Figure 2. Removal steps of battery pack Release the speakers cables from the cable guides in the direction shown by arrows 1. Detach the battery pack connector in the direction shown by arrow 2, remove the screws 3.
  • Page 40 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 2. Removal steps of battery pack (continued) Remove the battery pack in the direction shown by arrow 4.

  • Page 41: 1030 Pci Express Mini Card For Wireless Lan

    • “1020 Battery pack” on page 35 Important: The preinstalled WLAN module may only be replaced with a Lenovo approved module in order to comply with FCC and IC regulations. Refer to Table 4 “Parts list—Overall” on page 65 for Lenovo part numbers for the approved modules.
  • Page 42 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 3. Removal steps of PCI Express Mini Card for wireless LAN (continued) Remove the card in the direction shown by arrow 3. When installing: • In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled MAIN, and the grey cable (2nd) (AUX) into the jack labeled AUX on the card. • In models with a wireless LAN card that has three antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into the jack labeled 3, and the white cable (2nd) (AUX) into the jack labeled 2 on the card. • Apply the sponge to the card as shown below.

  • Page 43: 1040 Dimm

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1040 DIMM For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 Figure 4. Removal steps of DIMM Insert a flat blade tool into the memory module cover, and then remove the memory module cover manually. Release the two latches on both edges of the socket at the same time in the directions shown by arrows 1, and then unplug the DIMM in the direction shown by arrow 2.
  • Page 44 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 4. Removal steps of DIMM (continued) Check the position of the four clips as shown below. Align the memory module cover with the four clips as shown below. Make sure that the memory module cover has been engaged in the middle of...

  • Page 45: 1050 Hard Disk Drive

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1050 Hard disk drive For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. • Before removing the drive, suggest the customer to backup all the information on it if possible.
  • Page 46 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 5. Removal steps of hard disk drive (continued) Detach the HDD connector in the direction shown by arrow 2. Remove the hard disk drive from the slot in the direction shown by arrow 3. When installing: Make sure that the HDD connector is attached firmly. Remove the screws 4 and detach the metal frame from the hard disk drive. Step Screw (quantity) Color Torque M3 × 3 mm, Phillips-head, nylok-coated (4) Silver 1.5~2.0 kgf*cm hdd bracket---hdd module...

  • Page 47: 1060 Speakers

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1060 Speakers For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 • “1050 Hard disk drive” on page 41 Figure 6. Removal steps of speakers Unplug the speaker and backup battery connector 1,detach the touch pad connector 2. Then remove the speakers 3.

  • Page 48: 1070 Fan Assembly And Heat Sink Assembly

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual 1070 Fan assembly and Heat Sink assembly For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 Figure 7. Removal steps of fan assembly and Heat Sink assembly Release the cables from the cable guides in the direction shown by arrows 1. When installing: Route the antenna cables along the cable guides. As you route the cables, make sure that they are not subjected to any tension. Tension...
  • Page 49 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 7. Removal steps of fan assembly and Heat Sink assembly (continued) Unplug the fan connector in the direction shown by arrow 2. Remove the screws 3. Step Screw (quantity) Color Torque M2 × 4 mm, Phillips head, nylok-coated (2) Silver 1.0~1.5 kgf*cm fan---mb---log up & fan---log up When installing: Make sure that the connector is attached firmly.
  • Page 50 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 7. Removal steps of fan assembly and Heat Sink assembly (continued) Remove the screws 5. Step Screw (quantity) Color Torque M2 × 3 mm, Phillips head, nylok-coated (5) Black 1.0~1.5 kgf*cm cpu thermal module---cpu plate & vga thermal module---MB Lift the heat sink in the direction shown by arrows 6.
  • Page 51 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 7. Removal steps of fan assembly and Heat Sink assembly (continued) When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, to the part shown in the figure above. Either too much or too little grease application can cause a thermal problem due to imperfect contact with a component.

  • Page 52: 1080 Io Board, Dc-In Cable

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual 1080 IO board, DC-in cable For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 • “1070 Fan assembly and Heat Sink assembly” on page 44 Figure 8. Removal steps of IO board, DC-in cable Detach the IO board connector in the directions shown by arrows 1 and 2.
  • Page 53 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 8. Removal steps of IO board, DC-in cable (continued) Remove the IO board in the direction shown by arrow 4. Remove the DC-in cable in the direction shown by arrow 5. When installing: Make sure that the connector is attached firmly.

  • Page 54: 1090 System Board

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual 1090 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
  • Page 55 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 9. Removal steps of system board (continued) Remove the system board in the direction shown by arrow 7. Remove the screws 8. Step Screw (quantity) Color Torque M2 × 4 mm, Phillips-head, nylok-coated (2) Silver 1.0~1.5 kgf*cm RJ45 cover---M/B...
  • Page 56 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 9. Removal steps of system board (continued) Remove the RJ-45 door in the direction shown by arrow 9.

  • Page 57: 1100 Upper Case

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1100 Upper case For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 • “1030 PCI Express Mini Card for wireless LAN” on page 37 • “1050 Hard disk drive” on page 41 • “1060 Speakers” on page 43 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 IO board, DC-in cable” on page 48 • “1090 System board” on page 50 Figure 10. Removal steps of upper case Remove the screws 1. Step Screw (quantity) Color Torque M2.5 × 4.5 mm, Phillips-head, nylok-coated (4) 1.5 ~ 2.0 kgf*cm left side hinge---log up & right side hinge---log...
  • Page 58 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 10. Removal steps of upper case (continued) Open the hinge in the direction shown by arrows 2. Remove the upper case from the LCD module in the directions shown by arrow 3.

  • Page 59: Step Screw (Quantity)

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 10. Removal steps of upper case (continued) Remove the screws 4. Then remove the touchpad module 5. Step Screw (quantity) Color Torque M2 × 2 mm, Phillips-head, nylok-coated (2) Black 1.0~1.5 kgf*cm tp bracket---log up...

  • Page 60: 1110 Lcd Unit

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual 1110 LCD unit For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 • “1030 PCI Express Mini Card for wireless LAN” on page 37 • “1050 Hard disk drive” on page 41 • “1060 Speakers” on page 43 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 IO board, DC-in cable” on page 48 • “1090 System board” on page 50 • “1100 Upper case” on page 53 Figure 11. Removal steps of LCD unit Remove the LCD front bezel in the direction shown by arrows 3.

  • Page 61: M2 × 2.5 Mm, Phillips-Head, Nylok-Coated

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 11. Removal steps of LCD unit (continued) Remove the screws 2. Lift the LCD module slightly 3. Disconnect the connector in the direction shown by arrow 4. Then remove the LCD module. Step Screw (quantity) Color Torque M2 × 2.5 mm, Phillips-head, nylok-coated (4) Silver 1.0~1.5 kgf*cm lcd panel---lcd cover Detach the camera connector in the direction shown by arrow 5.
  • Page 62 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 11. Removal steps of LCD unit (continued) Remove the LCD cable in the direction shown by arrows 6. When installing: Make sure that the connector is attached firmly and that you do not pinch the antenna cables when you attach the LCD assembly. Route the LCD cable along the cable guides.

  • Page 63: 1120 Integrated Camera, Antenna Assembly And Lcd Hinges

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB 1120 Integrated camera, antenna assembly and LCD hinges For access, remove these FRUs in order: • “1010 Base cover” on page 33 • “1020 Battery pack” on page 35 • “1030 PCI Express Mini Card for wireless LAN” on page 37 • “1050 Hard disk drive” on page 41 • “1060 Speakers” on page 43 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 IO board, DC-in cable” on page 48 • “1090 System board” on page 50 • “1100 Upper case” on page 53 • “1110 LCD unit” on page 56 Figure 12. Removal steps of integrated camera, antenna assembly and LCD hinges Note: The integrated camera is stuck on the top center of the LCD cover.
  • Page 64 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Figure 12. Removal steps of integrated camera, antenna assembly and LCD hinges (continued) Peel off the adhesive tape securing the antenna boards, release the cables from the cable guide, and then remove the antenna assembly in the direction shown by arrows 2. Remove the screws 3. Step Screw (quantity) Color Torque M2 × 2 mm, Phillips-head, nylok-coated (6) Black 1.0~1.5 kgf*cm...
  • Page 65 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Figure 12. Removal steps of integrated camera, antenna assembly and LCD hinges (continued) Remove the LCD hinges in the direction shown by arrows 4.

  • Page 66: Locations

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Locations Front view and right-side view 1 Integrated camera 2 Built-in microphone 3 Computer display 4 Wireless LAN antennas 5 Ventilation slots 6 Power key 7 Touchpad 8 HDMI port 9 RJ-45 port J USB 3.0 port K Power status indicator...

  • Page 67: Bottom And Left-Side View

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Bottom and Left-side view 1 Louvers 2 Speakers 3 Kensington Mini Security slot 4 AC power adapter jack 5 Battery/Charging status indicator 6 USB 2.0 port 7 Combo audio jack 8 Memory card slot 9 Novo button...

  • Page 68: Parts List

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Parts list This section presents the following service parts: • “Overall” on page 65 • “LCD FRUs” on page 72 • “Miscellaneous parts” on page 74 • “AC adapters” on page 74 • “Screws” on page 79 • “Power cords” on page 71 Note: Each FRU is available for all types or models, unless specific types or models are specified. Attention: Do not attempt to replace an FRU on your own. If an FRU is damaged, contact a Lenovo authorized servicer or a marketing representative for replacement or repair. Only qualified technicians can inspect or repair this product.

  • Page 69: Overall

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Overall...
  • Page 70 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Table 4. Parts list—Overall ideapad ideapad FRU no. 510S-13ISK 510S-13IKB See “Miscellaneous parts” on page 74. LCD unit (see “LCD FRUs” on page 72). Upper Case C 80SJ BL BK W/KB US 5CB0L45206 ● ● Upper Case C 80SJ BL BK W/KB GK 5CB0L45217 ● ● Upper Case C 80SJ BLBKW/KBUSINT'E 5CB0L45423 ● ● ● Upper Case C 80SJ BL BK W/KB KO 5CB0L44999 ● ● Upper Case C 80SJ BL BK W/KB CH 5CB0L45099 ● Upper Case C 80SJ BL BK W/KB RU 5CB0L44973 ●...
  • Page 71 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 4. Parts list—Overall (continued) ideapad ideapad FRU no. 510S-13ISK 510S-13IKB Upper Case C 80SJ NBL BK W/KB TR 5CB0L45408 ● ● Upper Case C 80SJ NBL BK W/KB PO 5CB0L45250 ● ● Upper Case C 80SJ NBL BK W/KB LA 5CB0L45344 ● ● Upper Case C 80SJ NBL BK W/KBCF-E 5CB0L44957 ● ● Upper Case C 80SJ NBL BK W/KB ND 5CB0L45088 ● ● Upper Case C 80SJ NBL BK W/KB FR 5CB0L45082 ● ● Upper Case C 80SJ NBL BK W/KB GR 5CB0L45320 ●...
  • Page 72 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Table 4. Parts list—Overall (continued) ideapad ideapad FRU no. 510S-13ISK 510S-13IKB Upper Case C 80SJ NBLWH W/KB GK 5CB0L45154 ● ● Upper Case C 80SJ NBLWHW/KBUSINT'E 5CB0L44917 ● ● Upper Case C 80SJ NBLWH W/KB KO 5CB0L45185 ● ● Upper Case C 80SJ NBLWH W/KB CH 5CB0L45256 ● ● Upper Case C 80SJ NBLWH W/KB RU 5CB0L45395 ● ● Upper Case C 80SJ NBLWH W/KB AR-E 5CB0L45106 ●...
  • Page 73 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 4. Parts list—Overall (continued) ideapad ideapad FRU no. 510S-13ISK 510S-13IKB MB C 80SJ WIN I56200U R16M2GNBL 5B20L45397 ● MB C 80SJ NOK I36100U R16M2GNBL 5B20L45005 ● MB C 80SJ WIN I36100U R16M2GNBL 5B20L45076 ● MB C 80SJ NOK I76500U UMA NBL 5B20L45390 ● MB C 80SJ WIN I76500U UMA NBL 5B20L45258 ● MB C 80SJ NOK I56200U UMA NBL 5B20L45382 ● MB C 80SJ WIN I56200U UMA NBL 5B20L45377 ● MB C 80SJ NOK I36100U UMA NBL 5B20L45427 ● MB C 80SJ WIN I36100U UMA NBL 5B20L45168 ●...
  • Page 74 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Table 4. Parts list—Overall (continued) ideapad ideapad FRU no. 510S-13ISK 510S-13IKB WLAN, WIFI 1x1AC+BT4.0 (Non-Intel support SW10A11641 downgrade to BGN), Ltn NFA435 1x1AC+BT4.0 ● PCIE M.2 WLAN WLAN, WIFI 1x1AC+BT4.0 (Non-Intel SW10A11648 support downgrade to BGN), Cbt RTL8821AE ● ● 1x1AC+BT4.0 PCIE M.2 WLAN Wirelesslan_WIFI, Ltn NFA435A 1x1AC+BT4.0 SW10K97461 PCIE M.2 WLAN, WIFI 1x1AC+BT4.0 (Non-Intel ● support downgrade to BGN) WirelessLan_Non_Intel, Ltn NFA435A SW10K97461 1x1AC+BT4.0 PCIE M.2 WLAN, WIFI ● 1x1AC+BT4.0 (Non-Intel support downgrade to BGN) WirelessLan_Non_Intel, Cbt RTL8821AE SW10A11648 1x1AC+BT4.0 PCIE M.2 WLAN, WIFI...
  • Page 75 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 4. Parts list—Overall (continued) ideapad ideapad FRU no. 510S-13ISK 510S-13IKB HDD, 1TB 5400rpm, WD10SPCX-24HWST1 6G 16200554 ● ● 7mm 1T HDD HDD, 1TB 5400rpm, TSB MQ02ABF100 6G 7mm 5H20G09709 ● ● 5.4k 1TB HDD HDD, 1TB 5400rpm, TBD(QS sample: 2016/ ● FEB) HDD, 500G+8G Hybrid, ST500LM000 7mm 5H20H24608 ● 500G+8G HDD, 500G+8G Hybrid, Toshiba MQ02ABF050H 5H20H12631 ● 7mm 5.4k 500GB+8GB SSHD SSD, 128G 2.5'' SATA(low cost), Samsung 5SD0H45117 ● MZYLF128HCHP 2.5‘’ 5mm 128GB SSD SSD, 128G 2.5'' SATA(low cost),...

  • Page 76: Lcd Frus

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual LCD FRUs In Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB, there is following type of LCD. • “13.3-in. HD LED”...
  • Page 77 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 5. Parts list—LCD FRUs ideapad ideapad FRU no. 510S-13ISK 510S-13IKB ● ● LCD Bezel C 80SJ Black 5B30L45072 ● ● LCD Bezel C 80SJ Silver 5B30L45313 Panel, 13.3" Slim HD TN AG, AU B133XTN01.6 5D10K79643 ● ● 5A HDT AG S NB Panel, 13.3" Slim HD TN AG, IVO M133NWN1 R4 5D10H33278 ● ● HD AG S NB Panel, 13.3" Slim HD TN AG, BOE 18201050 ● ● HB133WX1-402 HD AG S LED1 NB LCD Panel, 13.3" slim FHD IPS AG, LGD LP133WF2- 5D10H11579 ●...

  • Page 78: Miscellaneous Parts

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Miscellaneous parts Table 6. Parts list—Miscellaneous parts ideapad ideapad FRU no. 510S-13ISK 510S-13IKB System miscellaneous parts: ● ● • a RJ45 Door C 80SJ Red 5D30L45416 ● ● • a RJ45 Door C 80SJ White 5D30L45121 ● ● • b HDD Bracket C 80SJ 5B40L45340 • c Dimm Emi Shielding C 80SJ 5S60L45308 ● ●...
  • Page 79 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 7. Parts list—2-pin AC adapters (continued) ideapad ideapad 510S-13ISK 510S-13IKB Adapter, Wall-mount 45W 2pin for UMA, Liteon PA-1450- 5A10H42922 ● ● 55LS 20V2.25A adapter Adapter, Wall-mount 45W 2pin for UMA, Liteon PA-1450- 5A10H42925 ● ● 55LU 20V2.25A adapter Adapter, Wall-mount 45W 2pin for UMA, Liteon PA-1450- 5A10H42918 ● ● 55LZ 20V2.25A adapter Adapter, Wall-mount 45W 2pin for UMA, Chicony 5A10H43629 ● ● ADL45WCA 20V2.25A adapter Adapter, Wall-mount 45W 2pin for UMA, Chicony 5A10H43618 ● ● ADL45WCB 20V2.25A adapter...
  • Page 80 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Table 7. Parts list—2-pin AC adapters (continued) ideapad ideapad 510S-13ISK 510S-13IKB Adapter, Wall-mount 65W 2pin for DIS, Liteon 5A10K78740 ● ● ADLX65CLGI2A 20V3.25A adapter Adapter, Wall-mount 65W 2pin for DIS, Liteon 5A10K78746 ● ● ADLX65CLGR2A 20V3.25A adapter Adapter, Wall-mount 65W 2pin for DIS, Liteon 5A10K78758 ● ● ADLX65CLGA2A 20V3.25A adapter Adapter, Wall-mount 65W 2pin for DIS, Liteon 5A10K78752 ● ● ADLX65CLGE2A 20V3.25A adapter Adapter, Wall-mount 65W 2pin for DIS, Liteon 5A10K78755 ●...
  • Page 81 Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 7. Parts list—2-pin AC adapters (continued) ideapad ideapad 510S-13ISK 510S-13IKB Adapter, Delta ADP-45DW B 20V2.25A COO, Wall-mount SA10M42785 ● 45W 2pin Adapter, Delta ADP-45DW D 20V2.25A COO, Wall-mount SA10M42696 ● 45W 2pin Adapter, Delta ADP-45DW H 20V2.25A COO, Wall-mount SA10M42699 ● 45W 2pin Adapter, Delta ADP-45DW G 20V2.25A COO, Wall-mount SA10M42774 ● 45W 2pin Adapter, Delta ADP-45DW E 20V2.25A COO, Wall-mount SA10M42748 ● 45W 2pin Adapter, Delta ADP-45DW C 20V2.25A COO, Wall-mount SA10M42700 ● 45W 2pin Adapter, Delta ADP-45DW K 20V2.25A COO, Wall-mount SA10M42804 ●...
  • Page 82 510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Table 7. Parts list—2-pin AC adapters (continued) ideapad ideapad 510S-13ISK 510S-13IKB Adapter, Chicony ADL45WCH 20V2.25A COO, Wall-mount SA10M42786 ● 45W 2pin Adapter, Delta ADLX65CDGC2A 20V3.25A COO, Wall- SA10M42764 ● mount 65W 2pin Adapter, Delta ADLX65CDGG2A 20V3.25A COO, Wall- SA10M42758 ● mount 65W 2pin Adapter, Delta ADLX65CDGU2A 20V3.25A COO, Wall- SA10M42765 ● mount 65W 2pin Adapter, Delta ADLX65CDGK2A 20V3.25A COO, Wall- SA10M42745 ● mount 65W 2pin Adapter, Delta ADLX65CDGI2A 20V3.25A COO, Wall- SA10M42796 ●...

  • Page 83: Screws

    Lenovo ideapad 510S-13ISK/ideapad 510S-13IKB Table 7. Parts list—2-pin AC adapters (continued) ideapad ideapad 510S-13ISK 510S-13IKB Adapter, Chicony ADLX65CCGE2A 20V3.25A COO, Wall- SA10M42760 ● mount 65W 2pin Adapter, Chicony ADLX65CCGB2A 20V3.25A COO, Wall- SA10M42707 ● mount 65W 2pin Screws Table 8. Parts list—screws Screw Pack C 80SJ 5S10L45147...

  • Page 84: Notices

    510S-13ISK/ideapad 510S-13IKB Hardware Maintenance Manual Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the...

  • Page 85: Trademarks

    Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo OneKey Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, products, or service names may be trademarks or service...

This manual is also suitable for:

Ideapad 510s-13ikb

Table of Contents