Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for INFINITY3DP X3
Summary of Contents for INFINITY3DP X3
- Page 1 User Manual...
- Page 2 4. X3 generates high temperatures as the nozzle can reach up to 500°C(932°F), the build plate up to 180°C (356°F) and the heated chamber up to 100°C (212°F) that may cause injury. Never reach inside of the X3 while it is in operation.
-
Page 3: Table Of Contents
TABLE SPECIFICATIONS ACCESSORIES CONFIRM BUILD PLATE INSTALLATION/REMOVE INTRODUCTION HARDWARE INSTALLATION PREPARATION WELCOME SETUP FILAMENT LOADING CONTENTS FILAMENT UNLOADING/REPLACEMENT START A PRINT COMPLETE A PRINT HEAT UP NOZZLE HEAT UP BUILD PLATE HEAT UP CHAMBER FAN SPEED OPERATION PRINT SPEED FLOW LIGHT LOCK (CHAMBER DOORS) SET UP *To be completed... -
Page 4: Specifications
PLA/ABS/Nylon/Carbon-Nylon/PETG/PC/Flexible/Glass Wool Filled PP/ASA PEEK/PEEK+CF/PEEK+GF/PEKK/PPSU/PPS Flexible Material Printable (Shore 50A) Connectivity SD card /USB Professional/Industrial-grade Power Input [100-120 V; 50/60 Hz; 12A or 200-240 V; 50/60 Hz; 7.5A]*2, total 1200W Slicer Cura Infinity3DP Edition Net Weight 67kg / 148 Ibs... - Page 5 ACCESSORIES 《 Please review and check the included accessories packed as below: 》 1. SD card *1 <plug on 3D printer> 2. Glue Sticks *1 3. PolyBox™ Edition II *1 4. Filament Holder *2 5. Power Cord (NEMA 5-15P to IEC C13 ) *2 (Option - 110v or 220v.) 6.
-
Page 6: Build Plate Installation/Remove
BUILDPLATEINSTALLATION/REMOVE 《The actions are limited to the cool-down (room temperature) build platform.》 REMOVE Step 1:Pull the board clip toward front as to loosen the build plate and platform. Step 2:Pull slightly up the build plate and apart the clips behind. - Page 7 BUILDPLATEINSTALLATION/REMOVE 《The actions are limited to the cool-down (room temperature) build platform.》 INSTALLATION Step 1:Insert with build plate to the clean build platform and tighten with the clips behind. Step 2:Buckle the board clips on the sides.
-
Page 8: Hardware Installation
《Please ensure the filament has a sharp tip before loading.》 Step 1: Connect two power cords to the side of X3. Step 2: Place filaments separately in the box and holder; insert the sharp-pointed tip of filaments into the side feedings... -
Page 9: Welcome Setup
WELCOMESETUP Step 1: Turn on the printer using the power switches on the side of X3. Step 2: The Actuator would move from side to side and back to home position. X, Y, Z-axis would run to home position and ready to print. -
Page 10: Filament Loading
FILAMENTLOADING 《Take the left hotend module as an example.》 Step 1: Select the“Left Nozzle”icon. If read successfully by X3, the control knob will be lighted-up . Step 2: Rotate the control knob allows you to set the temperature. Step 3: Press the control knob to complete the temperature settings; The nozzle would be heated up when the temperature is reached as setting. - Page 11 FILAMENTLOADING ※ It is available to open the top cover by pressing the RED button before operating the mentioned procedures. 《Take the left hotend module as an example.》 Please close the top cover after Step 1: Press the clip on the hotend module till the RED release button printing for maintaining the temperature in chamber.
-
Page 12: Filament Unloading/Replacement
FILAMENTUNLOADING/REPLACEMENT ※ Temperature set-up procedure, see P.07. 《Take the left hotend module as an example.》 Step 1: Heat up the nozzle until the filament melted with its target temperature. Step 2: Press the clip on the hotend module till the RED release button up as to loosen the filament. -
Page 13: Start A Print
Please loading ABS for your initial tested print. ※ Print with filament-PLA: We suggest opening the front door and top cover while Nozzle L Nozzle R printing. Otherwise, keep it closing while printing. Chamber X3 Files 3dp Files gear.gcode Prev BACK Next IX3_A.gcode... -
Page 14: Complete A Print
When the print finished, wait for the build plate cooling down and back to home position; take the print and build plate out of X3 then grab the print from it. ※ Once take apart the print from “heating build plate”,there would be possible injure or print defect. -
Page 15: Heat Up Nozzle
HEATUPNOZZLE 《Take the left hotend module as an example.》 Step 1: Select the“Left Nozzle”icon for setting temperature. If read successfully by X3, the control knob will be lighted-up. Step 2: Rotate the control knob to set the temperature. Step 3: Press the control knob to complete the temperature settings; The current temperature of nozzle would meet the target temperature. -
Page 16: Heat Up Build Plate
HEATUPBUILDPLATE Step 1: Select the “Build Plate” icon. If read successfully by X3, the control knob will be lighted-up and allow to set the temperature. Step 2: Rotate the control knob to set the temperature. Step 3: Press the control knob to complete the temperature settings; Current temperature of build plate would meet the target temperature. -
Page 17: Heat Up Chamber
HEATUPCHAMBER Step 1: Select the “Chamber ” icon. If read successfully by X3, the control knob will be lighted-up and allow to set the temperature. Step 2: Rotate the control knob to set the temperature. Step 3: Press the control knob to complete the temperature settings; The current temperature of chamber would meet the target temperature. - Page 18 FANSPEED Step 1: Select“Fan”icon. If read successfully by X3, the control knob will be lighted-up. Step 2: Rotate the control knob to set the fan speed (0%-100%). Step 3: Press the control knob to complete the setting. ※ The unit of temperature could be managed from the “gray toolbar ”on menu.
-
Page 19: Print Speed
PRINTSPEED Step 1: Select“Print Speed”icon. If read successfully by X3, the control knob will be lighted-up. Step 2: Rotate the control knob to set the print speed (0%-300%). Step 3: Press the control knob to complete the setting. ※ The initial print speed on printer will show 100%; the current print speed would meet the target speed. -
Page 20: Flow
FLOWRATE Step 1: Select “Flow”icon. If read successfully by X3, the control knob will be lighted-up. Step 2: Rotate the control knob to set the flow rate(0%-200%). Step 3: Press the control knob to complete the setting. ※ The unit of parameters could be managed from the “gray toolbar ”on menu. -
Page 21: Light
LIGHT Step 1: Select the“Light”icon and the chamber would be lighted up; off the light by press it again. IX3_A.gcode Nozzle L Nozzle R P . Time 0 days Status : 12 Hours 18 Minutes Chamber Progress : 23% 24 Seconds X : 122.75 Y : 155.00 Z : 47.50... -
Page 22: Lock (Chamber Doors)
LOCK(CHAMBERDOORS) Step 1: Select the“Lock”icon and the chamber door would be magnetic lock; unlock by press it again. IX3_A.gcode Nozzle L Nozzle R P . Time 0 days Status : 12 Hours 18 Minutes Chamber Progress : 23% 24 Seconds X : 122.75 Y : 155.00 Z : 47.50... -
Page 23: Set Up *To Be Completed
SETUP*Tobecompleted The function will be completed soon. IX3_A.gcode Nozzle L Nozzle R P . Time 0 days Status : 12 Hours 18 Minutes Chamber Progress : 23% 24 Seconds X : 122.75 Y : 155.00 Z : 47.50... -
Page 24: Calibration (Intro.)
CALIBRATION(INTRO.) Step 1: Select the“Calibration”icon, more items as following pages would be showed on the menu. Step 2: Select the“Return”icon to back to the homepage. Nozzle L Nozzle R Nozzle L Nozzle R Chamber Chamber 0.00 0.00 0.00 0.00 0.00 0.00... -
Page 25: Movement Of Right Hotend Module (X, Y, Z, E)
Step 1: Select the “Movement” icon for moving the right hotend module. Step 2: If read successfully by X3, you can select below items and the control knob will be lighted-up. (A) X Axis (B) Y Axis (C) Z Axis (D) Extruder Step 3: Adjust the parameter by rotating the control knob. -
Page 26: Z-Axis Zero Position
(it will clear all the record of Z-Axis), except for necessary calibration. CALIBRATION_ Z-AXIS ZERO POSITION (INITIAL) ※ Two nozzles (Left & Right) of X3 are both completed calibration before shipped out. ※ Please do the “Z-Axis Zero Position” after below actions: 1. - Page 27 ※ IDLE STATE – Calibration available. Step 4: (1) STOP printing (printer would be at idle state) and select “Left Hotend Calibration”icon. If read successfully by X3, the control knob will be lighted-up. (2) Select“Z-Axis”. (3) Adjust the parameters through the“gray toolbar ”on...
-
Page 28: X,Y,Z-Axis Home Position
X,Y,Z-AXISHOMEPOSITION Step 1: Select the“Home”icon for homing all three axis (X,Y,Z). Nozzle L Nozzle R Chamber X,Y,Z Home Position... -
Page 29: Hotend Replacement
HOTENDREPLACEMENT ※ Please ensure unloading the filament before operating the process. (see P. 33) ※ Please re-loading the filament (see P. 07-08) and operate the“Z-AXIS ZERO POSITION”(see P. 23) & “LEFT HOTEND CALIBRATION”(see P. 24) after finished hotend replacement. 《Take the left hotend module as an example.》 Step 1: Select“Change Nozzle”icon. - Page 30 HOTENDREPLACEMENT ※ Please ensure having the cool-down hotend and power off the X3 before operating the process. Step 2: Unplug the fan cable carefully and remove the fan module. Step 3: (A)Unplug the hotend cable/connector carefully (B)press the RED lever and (C)grab the hotend bottom slightly pull out.
-
Page 31: Build Plate Leveling
※ Please ensure having the glass build plate well locked with platform before operating the process. Step 1: Select “Build Plate Leveling” icon. If read successfully by X3, the control knob will be lighted-up and you can see the next page on menu. Build plate will automatically level to a designated height. -
Page 32: Belt
BELT Tuner ※ Please ensure the power switch is in the“off”position. Step 1: Download tuning Apps. (Key search“Tuner ”) Step 2: Separate two hotend modules to the sides. Tuner Slightly pulling the belt until reach the E major on tuning Apps as completed. - Page 33 BELT 《Failure to reach E major》 Step 3: Slowly move the Actuator to the center. (Please DO NOT quickly push the Actuator. This will lead to damages by causing reverse current.) SLOW...
- Page 34 BELT Step 4: Use the 2.5 mm hex wrench to loosen the screws on sides of the Actuator and adjust the belts. *Clockwise: Tighten the belt *Counterclockwise: Loosen the belt *Top-side screw of the Actuator: control the upper belt *Bottom-side Screw of the Actuator: control the bottom belt.
- Page 35 BELT Step 5: Slowly move the Actuator back to side and repeat the steps above until it reaches E major SLOW...
-
Page 36: Extruder
Step 2: Press the clip on the hotend module till the RED release button up as to loosen the filament. Step 3: Insert gently with the existed filament (A), and pull it out (B); turn off the X3. Nozzle L Nozzle R ※... - Page 37 EXTRUDER Step 4: Clean the gears (in circle as figure) with steel brush, pin or utility knife as to pick out small filament particles.
- Page 38 TROUBLESHOOTING Daily Maintain ● Wipe the enclosure of X3 with dry towel. ● DO NOT clean the panel display with alcohol. ● Remove dust or plastic particle on fan blades by tweezers. Print Issues 3D Printer Stringing (1)Reduce the print speed.