Advertisement
Available languages
Available languages
24V
SPEKTRUM+ RGBTW (IP54) PRO KIT
INSTALLATION INSTRUCTIONS
SPK-RGBTW-PROKIT-13
CUTTING & LINKING TAPE LIGHT (See Figures 2-7):
Do not exceed the maximum tape light run length of 13.1 feet in any single run. Use only the 24V DC power supply provided.
Cut increments are clearly marked on the tape light (every 3.94"). Cutting elsewhere will void warranty. Ensure an even cut along the edge of the copper conductors,
leaving the exposed copper conductor on the piece of tape light to be used, to ensure enough surface area is exposed for snap connector pins to make contact (see
Figure2). When using clamshell connectors, gently scrape off a small amount of the nano-coating that covers each of the 6 conductors on the tape light to ensure a
solid connection.
Making a Tape-to-Tape Connection (See Figures 3-5):
1. Ensure the polarity of the conductors on the two pieces of tape light to be connected are aligned. See Figure 3.
2. Using a tape-to-tape HD connector, open both sides of the connector so the metal teeth inside are exposed. See Figure 4.
3. Peel a small portion of the protective backing from the tape light on the end to be connected, then insert cut tape light end so the
copper pad conductors are aligned with the metal teeth inside.
4. Close snap connector and use pliers to ensure the connector "snaps" through the tape light. See Figure 5.
Making a Tape-to-Wire Connection (See Figures 6-9):
1. Using a tape-to-wire HD connector, follow steps 1-4 from "Making a Tape-to-Tape Connection" above to connect tape light.
2. Ensure polarity of the conductors on the connected piece of tape light and the polarity of the wires align. See Figure 6.
3. Cut desired length of wire from the 15ft reel of wire included being sure to leave approximately 1/2' on each end to be connected.
4. Separate wires slightly so they fit in the grooves of the snap connector. There is no need to strip the wire. See Figure 7.
5. Insert the cut wire into the slots of the snap connector so the wire is aligned with the metal teeth inside. See Figure 8.
6. Close snap connector and use pliers to ensure the connector "snaps" through the wire. See Figure 9.
FIGURE 2
FIGURE 6
Black
+24V DC
Green
G
Red
R
Blue
B
W White
WW
C White
CW
CONTROLLING THE TAPE LIGHT: The in-line LED controller/receiver utilizes
Bluetooth® Wireless Technology and can be controlled via the Spektrum+ Smart
Lighting App. It is not intended to be used with a standard dimmer switch.
USING THE REMOTE CONTROLLER (See Figure 10): Do not remove protective
film from battery compartment until ready to use. This remote includes a
3V CR2032 battery, only replace with the same type battery. Please dispose of
old batteries properly.
USING REMOTE WITH SPEKTRUM+ SMART LIGHTING APP: Add the remote to
the app by selecting "Add Device", then pressing and holding the On + Off button
together for 3 seconds to enter configuration mode. Follow the app instructions to
finish binding the remote. Within the app, select the remote to add devices to be
controlled by the remote. The remote can be added to specific rooms as well.
DISTANCE OF CONTROL CAPABILITY: 25 meters (approx. 80ft)
RESET THE REMOTE CONTROLLER: Press and hold Off and Scene buttons together
for 5 seconds.
USING THE SPEKTRUM+ SMART LIGHTING APP: Please follow the Spektrum+
Smart Lighting App guide.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
©2021 American Lighting, Inc. REV2124 www.AmericanLighting.com
FIGURE 3
Black
+24V DC
Green
G
Red
R
Blue
B
W White
WW
C White
CW
FIGURE 7
FIGURE 4
FIGURE 8
FIGURE 10
Adjust color
temperature
2700K-6000K
8 preset steps
Press for On
Press for Off
Page 2 of 4
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
FIGURE 5
FIGURE 9
Press & Hold to
Save a Scene
Press for Scene
Recall
Cycle through 10
preset RGB colors
Press & Hold for
Brightness Up
Press & Hold for
Brightness Down
Advertisement
