Attaching Shoulder Strap - Makita DUB363 Instruction Manual

Attaching shoulder strap

CAUTION:
Be sure to attach the hooks of
the shoulder strap to the machine securely. If the
hooks are attached incompletely, they may come off
and cause an injury.
CAUTION:
Be sure to use the shoulder strap
dedicated to this machine. Using other shoulder
strap may cause an injury.
CAUTION:
When you use the machine in com-
bination of the backpack-type power supply such
as portable power pack, do not use the shoulder
strap included in the machine package, but use
the hanging band recommended by Makita.
If you put on the shoulder strap included in the
machine package and the shoulder harness of the
backpack-type power supply at the same time,
removing the machine or backpack-type power supply
is difficult in case of an emergency, and it may cause
an accident or injury. For the recommended hanging
band, ask Makita Authorized Service Centers.
Attach the hooks of the shoulder strap to the machine
as shown in the figure.
► Fig.6: 1. Hook
The shoulder strap features a means of quick release.
Simply squeeze the sides of the buckle to release the
machine from the shoulder strap.
► Fig.7: 1. Buckle
► Fig.8: 1. Buckle
Assembly for vacuuming
CAUTION:
When performing the vacuuming
operation, always attach the suction nozzle to the
suction pipe.
CAUTION:
For safe operation, the suction
nozzle cannot be removed from the suction pipe,
once they are assembled. Do not remove the suc-
tion nozzle forcibly after the assembly. Otherwise,
they may be damaged.
Installing or removing suction pipe
and nozzle
Optional accessory
1.
Align the triangle mark on the suction nozzle with
that on the suction pipe, and then insert the suction
nozzle into the suction pipe until the latch on the nozzle
snaps into place.
► Fig.9: 1. Suction nozzle 2. Suction pipe 3. Triangle
mark
2. Loosen the bolt on the fan cover using the hex
wrench, and open the fan cover.
► Fig.10: 1. Bolt 2. Fan cover 3. Hex wrench
3. Align the triangle mark on the suction pipe
with mark on the main unit, and then attach the
suction pipe to the main unit.
► Fig.11: 1. Suction pipe 2. Triangle mark 3.
4. Turn the suction pipe clockwise so that the bolt
on the pipe is aligned with the hole on the main unit,
and then fasten the bolt firmly using the hex wrench to
secure the pipe to the main unit.
► Fig.12: 1. Suction pipe 2. Bolt
To remove the suction pipe and nozzle, perform the
installation procedure in reverse.
Installing or removing elbow pipe
and dust bag
Optional accessory
1. Insert the elbow pipe into the dust bag and tighten
the belt to fix the elbow pipe as shown in the figure.
► Fig.13: 1. Dust bag 2. Elbow pipe 3. Belt
2. Attach the elbow pipe to the main unit.
Insert the elbow pipe into the main unit with the bolt
facing left as shown in the figure. Turn the elbow pipe
as shown in the figure so that the bolt is aligned with the
hole on the main unit, and then tighten the bolt firmly
using the hex wrench.
► Fig.14: 1. Bolt 2. Elbow pipe
3. Attach the hook of the dust bag to the sub handle
as shown in the figure.
Adjust the length of the strap, and then fold extra strap
and fix it with hook and loop fastener.
► Fig.15: 1. Hook 2. Sub handle
4.
Attach the hooks of the shoulder strap to the carry
handle and sub handle as shown in the figure.
Make sure that the buckle is on the carry handle side.
► Fig.16: 1. Hook 2. Carry handle 3. Sub handle
4. Buckle
To remove the dust bag and elbow pipe, perform the
installation procedure in reverse.
When installing the small dust bag, open the fastener,
then insert the elbow pipe into the dust bag, and then
close the fastener. Lock and tighten the belt to fix the
elbow pipe.
► Fig.17: 1. Fastener 2. Dust bag 3. Belt 4. Elbow
pipe
mark
13 ENGLISH