• Bluetooth 4.1 • Invisible beauty with custom design • Bluetooth intercom up to 1.6 kilometer (1.0 miles)* Thank you for choosing the Schuberth SC10U for E1/C3PRO/C3 Basic. With the SC10U, you can call handsfree on your Bluetooth mobile • Four-way intercom phone, listen to stereo music or voice instructions of GPS navigations •...
SC10U 3 INSTALLING THE SC10U ON YOUR HELMET • Hook and Loop Fasteners for Speakers Status LED Main Unit DC Power Charging & • Foam Speaker Covers Firmware Upgrade Port • Speaker Pads Speakers Headset Buttons • USB Power & Data Cable Antenna Microphone...
SC10U 3.1 Installing the Main Unit 3. Insert the main unit between the external shell and the inner shell. Align its snap holders with the rear snaps. 1. Before you install the SC10U, remove the cheek pads and ear pads of your helmet. 2.
Page 9
SC10U 4. Peel off each cover of the hook and loop fasteners for speakers 5. Attach the speakers to the hook and loop fasteners for speakers to expose the adhesive surface. Then, attach the fasteners to the inside the helmet. Then click the snaps through the snap holders. ear pockets inside the helmet.
Page 10
SC10U 6. Insert the control buttons and microphone unit between the Note: external shell and the left inner shell. Click the snap through its To enhance the audio quality, you can make use of the foam speaker snap holder. covers. Cover each speaker with the foam and attach the hook fastener at the back of the speaker.
SC10U 4.3 Charging 4 GETTING STARTED You can charge the headset by connecting the supplied USB power & data cable into a computer’s USB port or USB wall charger. You can use any standard micro USB cable to charge the unit. You can also charge it on the road using the cigarette charger.
SC10U 4.4 Checking the Battery Level 4.5 Volume Adjustment You can easily adjust the volume by tapping the (+) Button or the (-) 4.4.1 LED Indicator Button. You will hear a beep when the volume reaches the maximum or When the headset is powering on, the red LED flashes rapidly minimum level.
You can information on downloading the Device Manager, please visit pair the SC10U with Bluetooth mobile phones, Bluetooth stereo oemsena.com/oem-schuberth/. devices such as MP3 players, or motorcycle specific Bluetooth GPS 4.6.2 Sena Smartphone App navigation, and with other Sena Bluetooth headsets.
SC10U 5.1 Mobile Phone Pairing - Mobile Phone, Bluetooth 5.2 Second Mobile Phone Pairing - Second Mobile Stereo Device Phone, GPS, and SR10 Typical Bluetooth headsets can connect with only one Bluetooth 1. Press and hold the (+) Button or the (-) Button for 10 seconds until device, but a second mobile phone pairing allows the headset to you hear the voice prompt, “Configuration menu”.
SC10U 5.3 Advanced Selective Pairing - A2DP Stereo or Note: Handsfree 1. If you have two audio (A2DP) devices connected to your headset then When you are using a smartphone, sometimes you may need to the audio from one device will interrupt the audio from the other device. selectively use the SC10U for A2DP stereo music only or for mobile For example, if you are playing music from the primary mobile phone, phone handsfree only.
SC10U 5.3.1 A2DP Stereo Music Only 6 MOBILE PHONE, GPS, SR10 1. To enter the voice configuration menu, press and hold the (+) Button or the (-) Button for 10 seconds until you hear the voice prompt, “Configuration menu”. 2. Tap the (+) Button until you hear the voice prompt, “Media 6.1 Mobile Phone Call Making and Answering selective pairing”.
SC10U 4. After selecting the last number redial menu, you will hear a voice Note: prompt, “Last number redial”. Then, to redial the last phone call 1. If you have two phones connected to your headset and you have an number, tap the (-) Button.
SC10U 6.3 GPS Navigation 7 STEREO MUSIC If you pair a Bluetooth GPS to the SC10U as described in section 5.2, “Second Mobile Phone Pairing - Second Mobile Phone, GPS, and SR10” , you can listen to GPS instructions wirelessly. Tap the (+) Button or the (-) Button to adjust volume.
SC10U 7.2 Music Sharing 8 INTERCOM You can start sharing music with an intercom friend using Bluetooth stereo music during a two-way intercom conversation (please refer to section 8.2, “Two-way Intercom” ). When you terminate music sharing, To enter the intercom pairing mode, call intercom friends, or start you can go back to the intercom conversation.
SC10U 8.1 Intercom Pairing 4. Simply tap the (+) Button of any one of the two headsets A or B and wait until the LEDs of both headsets turn to blue and intercom 8.1.1 Pairing with Other SC10U Headsets for Intercom connection is automatically established.
SC10U 8.2 Two-way Intercom 6. The intercom pairing queue is ‘Last-Come, First-Served ’. If a headset has multiple paired headsets for intercom conversations, 8.2.1 Starting Two-way Intercom the last paired headset is set as first intercom friend. The You can start an intercom conversation with one of any intercom previous intercom friend becomes second intercom friend, and friends by tapping the (-) Button within the intercom menu.
SC10U 8.3 Three-way Intercom 2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom 8.3.1 Starting Three-way Intercom conversation with the intercom friend (B). Or intercom friend (B) You (A) can have a three-way conference intercom with two other may start an intercom call with you (A).
SC10U 8.4 Four-way Intercom 4. Now you (A) and two SC10U intercom friends (B & C) are having a three-way conference intercom. 8.4.1 Starting Four-way Intercom You can have four-way conference intercom with three other SC10U users by adding one more intercom participant to the three-way intercom.
SC10U 2. Tap or double tap the (-) Button within the intercom menu to 9 THREE-WAY CONFERENCE PHONE CALL disconnect the intercom connection with one of the two intercom friends accordingly. However, when you disconnect the second WITH INTERCOM PARTICIPANT friend (C) by double tapping the (-) Button within the intercom menu, you will be disconnected with the third participant (D) as well.
SC10U 2. When you have an incoming intercom call during a mobile phone 10 GROUP INTERCOM call, you will hear 4 high toned beeps, alerting you that there is an incoming intercom call. You will also hear a voice prompt, “Intercom requested”.
SC10U 1. If a non-Sena headset does not support a multipoint connection, 11 UNIVERSAL INTERCOM it cannot use a phone call connection while using the Universal Intercom. 2. As for Sena headsets, the Universal Intercom affects the multipoint You can have an intercom conversation with non-Sena Bluetooth connection.
SC10U 11.1 Universal Intercom Pairing 11.2 Two-way Universal Intercom The SC10U can be paired with non-Sena Bluetooth headsets for You can initiate the Universal Intercom connection with non-Sena Bluetooth intercom conversation. You can pair the SC10U with only Bluetooth headsets using the same intercom connection method as one non-Sena Bluetooth headset so if you pair with a different non- you would between other Sena headsets.
SC10U 11.3 Three-way Universal Intercom 2. Start an intercom conversation with non-Sena Bluetooth headset (B) in your intercom group. For example, you (A) may start an You may make a three-way Universal Intercom connection with two intercom conversation with non-Sena Bluetooth headset (B). The SC10Us and one non-Sena Bluetooth headset.
SC10U 11.4 Four-way Universal Intercom 4. Now you (A), non-Sena Bluetooth headset (B), and the other SC10U (C) are having a three-way conference intercom. You may make a four-way Universal Intercom connection with a couple of different configurations, 1) three SC10Us and one non-Sena Bluetooth headset or 2) two SC10Us and two non-Sena Bluetooth headsets .
Page 30
SC10U 11.4.1 Four-way Universal Intercom Case 1 3. The non-Sena Bluetooth headset (D) may join the conference intercom by making an intercom call to the SC10U (C). Two SC10U headsets (A and C) and two non-Sena Bluetooth headsets (B and D). 1.
SC10U 11.4.2 Four-way Universal Intercom Case 2 12 FM RADIO Three SC10U headsets (A, C and D) and one non-Sena Bluetooth headset (B). The procedure is the same as case 1 described in section 11.4.1 . 12.1 FM Radio On and Off To turn on the FM radio, press the (-) Button for 5 seconds until you hear a mid-toned double beep sound.
SC10U Note: 13 FUNCTION PRIORITY 1. You can save FM stations to presets before using FM radio. Connect the SC10U to your PC and open the Sena Device Manager. It allows you to save up to 10 FM station frequency presets on the SC10U settings menu. The SC10U operates in the following order of priority: You may do the same operation by using the Sena Smartphone App.
SC10U The voice prompt for each menu item is as below: 14 CONFIGURATION SETTING (1) Phone pairing (10) Voice prompt (2) Second mobile phone pairing (11) RDS AF setting (3) Phone selective pairing (12) Sidetone (4) Media selective pairing (13) Noise control You can set the configuration of the SC10U by the voice menu (5) Speed dial (14) Delete all pairings...
SC10U 14.1 Mobile Phone Pairing Phone pairing Voice Prompt “Phone pairing” Second mobile phone pairing Factory Default Phone selective pairing Media selective pairing To go into mobile phone pairing mode, tap the (+) Button until you hear the voice prompt, “Phone pairing”. Please refer to section 5.1, Speed dial “Mobile Phone Pairing - Mobile Phone, Bluetooth Stereo Device”...
SC10U 14.3 Phone selective pairing 14.5 Assigning Speed Dial Voice Prompt “Phone selective pairing” Voice Prompt “Speed dial” Factory Default Factory Default Execute Tap the (-) Button To go into phone selective pairing mode, tap the (+) Button until you hear the voice prompt, “Phone selective pairing”.
SC10U 14.7 Enabling/Disabling Voice Activated Phone Note: Answering 1. After assigning a phone number to one of three speed dials, you can continually assign another phone number to the rest of two speed dials. Voice Prompt “VOX phone” 2. You can also assign phone numbers for speed dialing by using the Sena Factory Default Enable Device Manager software or the Sena Smartphone App.
SC10U 14.8 Enabling/Disabling Voice Activated Intercom 14.9 Enabling/Disabling HD Intercom Voice Prompt “VOX intercom” Voice Prompt “HD intercom” Factory Default Disable Factory Default Enable Enable/Disable Tap the (-) Button Enable/Disable Tap the (-) Button If this feature is enabled, you can initiate an intercom conversation HD Intercom enhances the two-way intercom audio from normal with the last connected intercom friend by voice.
SC10U 14.10 Enabling/Disabling Voice Prompts 14.12 Enabling/Disabling Sidetone Voice Prompt “Voice prompt” Voice Prompt “Sidetone” Factory Default Enable Factory Default Disable Enable/Disable Tap the (-) Button Enable/Disable Tap the (-) Button You can disable voice prompts by configuration setting, but the Sidetone is audible feedback of your own voice.
SC10U 14.14 Delete All Bluetooth Pairing Information 14.16 Universal Intercom Pairing Voice Prompt “Delete all pairings” Voice Prompt “Universal intercom pairing” Factory Default Factory Default Execute Tap the (-) Button Execute Tap the (-) Button To delete all Bluetooth pairing information of the SC10U, tap the (+) To enter into Universal Intercom Pairing mode, tap the (+) Button until Button until you hear a voice prompt, “Delete all pairings”, and tap you hear a voice prompt, “Universal intercom pairing”.
SC10U 14.18 Exit Voice Configuration Menu Tap (+) Button Tap (-) Button Voice Prompt “Exit configuration” Phone Pairing None Factory Default Second Mobile Phone Pairing None Execute Tap the (-) Button Phone Selective Pairing None To exit voice configuration menu and get back to stand-by mode, tap Media Selective Pairing None the (+) Button until you hear a voice prompt, “Exit configuration”,...
SC10U Tap (+) Button Tap (-) Button 15 REMOTE CONTROL Remote Control Pairing Execute Universal Intercom Pairing Execute You can remotely control the SC10U via Bluetooth using the Remote Factory Reset Execute Control (sold separately). This eliminates the need to take off your hand for button operations.
Device Manager” ). Please visit Sena Bluetooth website at oemsena. When you try to start an intercom conversation with an intercom friend com/oem-schuberth/ to check the latest software downloads. who is unavailable within range or already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal.
SC10U 17.3 Fault Reset 18 QUICK OPERATION REFERENCE When the SC10U is not working properly or is in faulty status for any reason, you may reset by pushing the pin-hole reset button as shown in the picture below. Insert a paper clip into the reset pin-hole and press the reset button for a second with light pressure.
Page 44
SC10U Type Function Button Command Beep Type Function Button Command Beep Press the (-) Button for Press the (-) Button for Mid-tone FM radio on/off 1 second 5 seconds double beeps Intercom pairing Mid-tone Press the (+) Button for Mid-tone Tap the (+) Button Red flashing FM Radio...
SC10U CERTIFICATION AND SAFETY APPROVALS • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected FCC Compliance Statement • Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is FCC RF Exposure Statement subject to the following two conditions: This equipment complies with FCC radiation exposure limits set forth...
SC10U Bluetooth License CE Declaration of Conformity The Bluetooth ® word mark and logos are owned by the Bluetooth SIG, This product is CE marked according to the provisions of the R&TTE Inc. and any use of such marks by Sena is under license. Other Directive (1999/5/EC).
SC10U SAFETY INFORMATION Product Use • In some regions, it is prohibited by law to ride motorcycles while Please ensure that the product is properly used by observing the wearing headsets or earbuds. Therefore be certain to comply with all warnings and cautions below to prevent any risk and/or damage to relevant laws in the region before using the product.
SC10U • When using the product, be certain to conform to laws regarding the • Any 3rd party USB charger can be used with Sena products if the use of communications devices while riding. charger is approved by either the FCC, CE, IC or other locally approved agencies that Sena accepts.
Here, product warranty extends to the product only. this agreement, and forfeiture of rights to all claims. If you do not Schuberth will not be liable for any loss, damage of human life, or loss consent to all the terms and conditions of this agreement, return the of property which may result from using the product beyond defective product for a refund.
Page 50
Schuberth and Sena (collectively In addition, usage of the product constitutes acceptance of all referred to as “the company”) recommend that, before using the terms and conditions regarding waiver of rights.
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE that may have occurred while you use the product. Further, Schuberth SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, will not be liable for any substantial damage not related to the FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF condition, environment, or malfunction of the product.
In addition to damages which may occur due to the use of the product, To obtain product warranty service, send the defective product, at Schuberth will not be liable for damages of the product which occur your expense, to the manufacturer or the seller along with proof of due to the following events.
Page 53
1.0.0 www.schuberth.com User's Guide for Firmware v1.0...
Need help?
Do you have a question about the 20013492 and is the answer not in the manual?
Questions and answers