Table of Contents
Advertisement
Install the product according to the directions in the user manual.
If the product is not installed based on the directions in the user manual, it
can cause a serious injury or damage to the product.
During the installation, check the type of wall material and use
the sealed anchor and screw if the conditions comply.
If you do not use the designated anchor or screw, the mount may not be
able to withstand the weight of the product and cause a safety issue.
Do not wipe the product with a wet towel and do not use any
heater or humidifier below where the product is installed.
If water flows into the product or if moisture and heat are applied to the
product, it can cause a fire, an electric shock or problem to the product.
Unplug the power cord from the power outlet before
installing the product.
If you install the product with the power cord plugged, it can cause an
electric shock or a fire.
Do not allow the video connectors connected to the display to
press against the wall. Use the included right-angle adapters if
needed.
Only use
attachments/accessories specified
Before installation
* Do not use the product for purposes other than mounting a display on the wall.
* When installing/using the wall mount, be cautious of product damage and avoid accidents.
* If you have not fully read and understood the installation manual, do not install the product and contact the dealer to have a
specialized installer install the product for you.
* Even if you are not a specialized installer, it is advantageous to have experience in mechanical or construction field in completely
understanding this manual and installing the product.
* This product is designed to be mounted to walls that use standard intervals between the studs.
* Install the screw to attach the wall mount so that it can be assembled at the center from both ends of the studs.
Use of stud finder, a separate device, is recommended.
* Install the product only on a vertical wall.
The manufacturer is not responsible for issue from installing the product on severely wall or on the ceiling.
* Keep the included accessories out of reach of babies or children as it can cause safety issues including suffocation from
swallowing the parts.
* Make sure screws are tight against the wall, but do not overtighten.
* Be careful not to install a TV that exceeds the weight restrictions of the wall mount.
* Be careful with the tools used during installation to prevent accidents or damage.
Installation method
- Tools you will need : Phillips head "+" driver(Manual or motorized)
You may also need an 8mm socket wrench or an 8mm drill bit for concrete.
- Installation method is described based on the PSW400 model. The actual product may differ from the picture.
Fixating the mounting bracket on the TV
1
- If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the
technical service manual.
Guide spacer
Caution
by the manufacturer.
<Work procedure>
1. Check to see if the display has screws installed into the mounting
holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw in order as
shown in the picture.
Lay the set down and secure the guide spacer and the set using the screws.
Guide spacer
- Put the product on the table placing the screen face down.
screw
When doing this, it is highly recommended to place a floor cushion or soft clothes on
the flat table before putting the product on it to avoid any damage of the screen surface.
- Tighten the screw until the set, guide spacer and the screw are fully pressing
against one another.
- Use the "+" driver (Manual or motorized) when tightening the screw.
When installing the product or adjusting the height of the
product after installing, always do so with 2 people.
Working alone can cause the product to fall off and result in injury or
damage to the product.
When drilling holes in the wall, always use a drill bit and
drill of designated diameter. Also follow the designated
directions for the depth of the hole.
If the product is installed without following the designated
method, the product may be unstable and cause a safety issue.
Donot install the product near any object that may cause
vibration.
Do not install the product near any high voltage power cable or power
source.
Do not install the product with bare hands. Always wear
proper work gloves.
It can cause an injury.
Ø4mm drill bit for wood or steel / Level / Stud finder / Drill.
3
Advertisement
Table of Contents
